Whirlpool B 10TC/CS BNV F Installationanleitung Und Betriebsanleitung Seite 15

Make sure you take all the necessary precautions to
guarantee proper installation in compliance with the
applicable norms in force regarding accident-prevention for
electrical connection. For the correct operation of the
appliance when built into the cabinet, it is vital that the
minimum distances illustrated in Fig. 3 be respected. The
hob features a type Y degree of protection against
overheating in compliance with norms. All surfaces adjacent
to the cabinet and the back panel should be made of
materials resistant to a temperature of 65°C.
Securing the appliance to the cabinet Securing the appliance to the cabinet Securing the appliance to the cabinet Securing the appliance to the cabinet Securing the appliance to the cabinet
There are three different groups of appliance as far as
installation is concerned:
BUILT-IN HOB
HEIGHT= STEEL THICKNESS
BUILT-IN HOB
STEEL TICKNESS <HEIGHT <75 mm
SIT ON - ON HOB
HEIGHT >75 mm
1- Built-in hobs to be slotted in (Class 3 - see 1- Built-in hobs to be slotted in (Class 3 - see 1- Built-in hobs to be slotted in (Class 3 - see 1- Built-in hobs to be slotted in (Class 3 - see 1- Built-in hobs to be slotted in (Class 3 - see
figure 4, detail H1). figure 4, detail H1). In this case it is necessary to make figure 4, detail H1).
figure 4, detail H1). figure 4, detail H1).
a hole in the worktop whose measurements match those of
the hob. The measurement at the side should be reduced
by 2 cm so as to ensure that 1 cm of the perimeter of the
hob overlaps with and rests on top of the supporting surface.
To slot in the hob flush with the worktop, the cut-out on this
supporting surface must be lowered (see figure 5), so that
both the edge of the hob and the seal under it can be
positioned there. Before fitting the hob to the worktop,
position the seal "X" "X" provided along the perimeter of the "X" "X"
"X"
hob, as illustrated in figure 5.
Hobs installation Hobs installation
Hobs installation Hobs installation Hobs installation
2-Built-in hobs (Class 3) with edges lower than 75 2-Built-in hobs (Class 3) with edges lower than 75
2-Built-in hobs (Class 3) with edges lower than 75 2-Built-in hobs (Class 3) with edges lower than 75 2-Built-in hobs (Class 3) with edges lower than 75
mm (see figure 4, detail H2). mm (see figure 4, detail H2). mm (see figure 4, detail H2). mm (see figure 4, detail H2). mm (see figure 4, detail H2). To install this type of hob,
a hole large enough to accommodate the whole lower casing
of the appliance must be made on the worktop intended to
be under the hob. Remember to leave a gap of at least 1 cm
between the lower casing and the worktop around the whole
perimeter of the appliance (the underside of the casing can,
however, touch the surface below it). To fit the appliances,
follow the instructions given above in point 1 or use any
supplementary instruction leaflet that is provided in special
cases.
Fig Fig Fig Fig.3 Fig
3-Sit-on hobs (Class 1) with edges higher than 75 mm 3-Sit-on hobs (Class 1) with edges higher than 75 mm 3-Sit-on hobs (Class 1) with edges higher than 75 mm
3-Sit-on hobs (Class 1) with edges higher than 75 mm 3-Sit-on hobs (Class 1) with edges higher than 75 mm
(see figure 4, detail H3). In this case, the lower casing of the (see figure 4, detail H3). (see figure 4, detail H3). (see figure 4, detail H3). (see figure 4, detail H3).
hob does not protrude further than the edge of the appliance.
Even when the hob is resting on the worktop, it will suffice to
leave space for the gas supply tube and electricity supply
cable. To fit this type of hob, follow the instructions below (fig.
6):
• Fix the two screws provided "A" at a distance from the
back panel as shown in figure 6, leaving the heads of the
screws sticking out of the wood by 1.5 mm.
• Hook the hob onto the two screws "A" and push it towards
the back.
• Fix the appliance to the cabinet at the rear, using the two
brackets "B" and the four screws "C" (these are all provided).
fig.6
N.B.: to make maintenance operations more efficient, the N.B.: to make maintenance operations more efficient, the
N.B.: to make maintenance operations more efficient, the N.B.: to make maintenance operations more efficient, the N.B.: to make maintenance operations more efficient, the
area around the hob must be easily accessible after it area around the hob must be easily accessible after it area around the hob must be easily accessible after it
area around the hob must be easily accessible after it area around the hob must be easily accessible after it
has been installed (i.e. there are no completely shut-off has been installed (i.e. there are no completely shut-off has been installed (i.e. there are no completely shut-off has been installed (i.e. there are no completely shut-off has been installed (i.e. there are no completely shut-off
elements). elements). elements).
elements). elements).
15 15
15 15 15
20 mm
fig.5
B C
A