Werbung
Verfügbare Sprachen
Verfügbare Sprachen
ENGLISH
Memory function
1.
Press and hold the single coffee icon
amount of coffee dispensed.
When the machine has preheated, the single coffee
2.
will stop flashing and remain fixed.
3.
After that, press and hold the single coffee icon
desired amount of espresso has been dispensed, press the single coffee icon
The machine will beep, indicating that the dispense time and dispensed amount of coffee
4.
have been saved correctly.
5.
The next time you press the single coffee icon
according to the last saved setting.
NOTE:
-
Only a maximum dispensing time of approx. 60 seconds can be set by default.
-
Do not stop the coffee dispensing too soon, since if the set dispensing time is insufficient,
the setting will not be saved.
-
Be sure to dispense a continuous amount of coffee of 40 ml.
NOTE:
-
The adjustable dispensing quantity of single espresso coffee ranges from 30 ml to 60 ml.
-
If you want to activate the memory function to prepare a double espresso, follow the steps
above, but press the double coffee icon
NOTE: the adjustable dispensing quantity of double espresso coffee ranges from 60 ml to 90
ml.
Restore factory settings
If you want to restore factory settings, press, and hold, at the same time, the single coffee
1.
icon
and the steam icon
for 3 seconds.
2.
Both icons will light up and the appliance will beep, indicating that the factory settings
have been reset correctly.
4. CLEANING AND MAINTENANCE
-
Unplug the appliance and allow it to cool down completely before cleaning.
-
Clean the outer housing of the machine with a damp cloth or sponge.
-
Do not use alcohol or cleaning solvents or immerse the machine in water for cleaning.
-
Remove the portafilter by turning it to the unlocked position and remove the coffee
grounds from the filter.
POWER ESPRESSO 20 COLDBREW
44
for 3 seconds to enter the setting mode for the
and the double coffee
to start brewing coffee. Once the
again.
to brew coffee, the machine will operate
.
Descaling
To ensure that the machine continues to work properly, that the internal pipes are clean, and
that the coffee retains its full flavour, it is necessary to descale the machine regularly.
icons
To know exactly when to do this, the machine will display a descaling warning when it has
performed 300 complete extraction cycles. During this warning signal, all icons will start
flashing and the machine will beep 5 times. It will then return to its normal operating state.
NOTE: the descaling warning will be displayed every time you switch on the machine if you do
not cancel it.
Procedure for removing limescale deposits
Fill the tank with a solution of water and descaling agent up to the "MAX" mark. The
1.
optimum proportion is one part decalcifying liquid to four parts water. For further
information, please refer to the manufacturer's label. Use a household descaler. You can
also use citric acid instead of descaling liquid. In this case, add three parts citric acid and
two parts water.
2.
Press the double coffee icon to dispense about 100 ml of hot water. Then, switch off the
coffee machine and leave the solution to act for 5 minutes.
3.
Switch the machine back on and repeat step 3 twice, filling the tank with tap water up to
the "MAX" mark (there is no need to wait for 5 minutes).
4.
Once the descaling process has been completed, cancel the warning manually. To do this,
press and hold
Cooling function
1.
If you wish to prepare coffee after steaming, you must first deactivate the function by
pressing the steam icon
2.
If
and
down. To do so, turn the steam knob to the ON position
pumping and dispenses water through the steamer to cool down the machine. Fig. 5
3.
When the corresponding icon starts flashing quickly, turn the steam knob to the OFF
position to stop the cooling process. When the power icon lights up, you can start brewing
coffee again.
,
and
at the same time for 3 seconds.
.
flash, the temperature of the machine is too high and needs to be cooled
POWER ESPRESSO 20 COLDBREW
ENGLISH
so that the machine starts
45
Werbung
