Weber Rescue Systems STABFAST ALU+ Bedienungsanleitung Seite 15

Points to watch during use
IMPORTANT
While freeing the casualty, check the stabilisers constantly. Check:
1. The tension of the straps. Tighten if necessary.
2. Ensure that the head of the strut is secure and does not move; if necessary secure it by use of a line from the eye
link to the vehicle.
3. That the foot of the stabiliser strut is not sagging or sliding.
4. That the adjustable wedge has not shifted.
5. The attachment of the finger hook to the vehicle.
After use
1. Loosen the straps using the ratchet (position 3).
IMPORTANT
If the vehicle is lying on its roof, loosen both straps simultaneously.
2. Collapse the telescopic struts.
3. Roll up the straps with the strap retractor.
4. Check that the set is complete when packing it away.
Clean and inspect the set as described under: "Maintenance and inspection After every use."
5.
Stabilising a vehicle lying on its side
1. Position stabiliser strut 1 with the green strap underneath the vehicle at the front (engine end). Extend the stabiliser strut to its
maximum length. Hook the finger hook into the vehicle as low as possible, don't hook into moving parts, such as struts, support arms,
etc.
IMPORTANT
If the exhaust is hot, place a wooden board between it and the strap to protect the strap. Place the red protective sleeve in front of any
sharp objects. Using the ratchet, tighten the strap fully. sharp objects. Using the ratchet, tighten the strap fully.
2. 2. 2. Position stabiliser strut 2 with the yellow strap at the front of the vehicle (bonnet end). Extend the stabiliser strut to its maximum Position stabiliser strut 2 with the yellow strap at the front of the vehicle (bonnet end). Extend the stabiliser strut to its maximum
length, attach it to the vehicle at the lowest level possible, using the finger hook or using the hook blade, make an incision in the length, attach it to the vehicle at the lowest level possible, using the finger hook or using the hook blade, make an incision in the
bonnet* as low down as possible. Hook the finger hook into the incision. Slide the red protective sleeve in front of any sharp objects.
Using the ratchet, tighten the strap fully.
NOTE
If possible, open the bonnet first and look for a firm point before making an incision with the finger hook.
3. 3. 3. Tighten the straps on both sides again. Check that both straps are taut. Tighten the straps on both sides again. Check that both straps are taut.
IMPORTANT IMPORTANT IMPORTANT
Do not lift the vehicle.
4. 4. 4. Place stabiliser strut 3 with the blue strap underneath the vehicle at the back. Undo the strap at the bottom of the Place stabiliser strut 3 with the blue strap underneath the vehicle at the back. Undo the strap at the bottom of the
stabiliser strut. Pass the loose strap through the roller in the tip of the adjustable wedge. Reattach the strap to the stabiliser strut. Pass the loose strap through the roller in the tip of the adjustable wedge. Reattach the strap to the
bottom of the stabiliser strut. bottom of the stabiliser strut.
IMPORTANT
Check that the strap is secure. Place the adjustable wedge under the vehicle at the back (boot end).
IMPORTANT IMPORTANT IMPORTANT
If the exhaust is hot, place a wooden board between it and the strap to protect the strap. Place the red protective sleeve in front of any If the exhaust is hot, place a wooden board between it and the strap to protect the strap. Place the red protective sleeve in front of any
sharp objects. Tighten the strap until the vehicle is lifted a little way onto the adjustable wedge. sharp objects. Tighten the strap until the vehicle is lifted a little way onto the adjustable wedge. sharp objects. Tighten the strap until the vehicle is lifted a little way onto the adjustable wedge.
5. 5. 5. The vehicle is now stabilised. The vehicle is now stabilised.
MANUAL
STABFAST
Stabilisation
ALU +
TM
systemSTABFAST
+
ALU
TM
15