Symbols On The Product; Intended Use; Foreseeable Misuse; Operator Training - Cleco Neotek 30-Serie Bedienungsanleitung

1
EN
Structure Of Warnings
Caution
Type and source of danger.
Possible consequences of non-observance.
► Measures to avoid danger.
2.2

Symbols on the Product

Electric voltage
Read the operating instructions carefully
CE compliant
The product corresponds to the prescribed
technical requirements in Europe.
UKCA compliant.
The product corresponds to the prescribed
technical requirements in Great Britain.
UL certified
The product complies with the prescribed
technical requirements of the Mexican
market.
Observe and comply with all local disposal
guidelines for all components of this equip-
ment and it's packaging.
2.3

Intended Use

The user is liable for any damage caused by improper
use. Use the product only under the following conditions:
•
Use only in industrial tightening processes.
•
Only in conjunction with the components listed in the
EU Declaration of Conformity.
•
Under the prescribed ambient conditions.
•
Within the power range, which is specified in the tech-
nical data.
•
With equipment parameters set up properly.
•
In EMC Limit Class A (electromagnetic immunity for
industrial areas). For the currently observed EMC
standards, see the EU Declaration of Conformity.
•
With the recommended battery and charger.
2.4

Foreseeable misuse

► DO NOT use the product as a hammer.
► DO NOT use a controller other than the one listed in
the EC Declaration of Conformity.
► DO NOT use the product in areas where there is a
risk of explosion.
► DO NOT use the product in damp spaces or outdoors.
► DO NOT disassemble or modify the product.
2.5

Operator Training

The tool has been preset by Apex Tool Group. Changes to
the default settings can only be made by a qualified em-
1
ployee .
1
Qualified employees have the training and experience to
identify potentially hazardous situations. They can initiate
6
2.6

Standards

It is mandatory that national, state, and local codes and
standards be followed.
FCC- and IC Compliance
This product complies with Part 15 of the FCC Rules. Any
changes or modifications not expressly approved by the
manufacturer could void the user's authority to operate this
product. Operation is subject to the following two condi-
tions:
•
This product may not cause harmful interference.
•
This product must accept any interference received,
including interference that may cause undesired oper-
ation.
FCC Responsible party
Name: William Cain
Position: Director, R&D
Address: 670 Industrial Drive
Lexington, SC 29072
United States
Phone: +1 803 951 7558
Email: William.Cain@ClecoTools.com
This product has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide rea-
sonable protection against harmful interference when the
product is operated in a commercial environment. This
product generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to
radio communications.
Operation of this product in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at his own expense.
2.7

General Power Tool Safety Warnings

Read all safety warnings, instructions, illustrations
and specifications provided with this power tool. Fail-
ure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future refer-
ence.
The term "power tool" in the warnings refers to mains-op-
erated (corded) power tool or battery-operated (cordless)
power tool.
1 Work area safety
a) Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b) Do not operate power tools in explosive atmos-
pheres, such as in the presence of flammable
appropriate safety measures and are obliged to comply
with regulations.
TM12-1109 | REV G l 2023-09 Apex Tool Group