Fisher Studio-Standard TACM92 Bedienungsanleitung Seite 21

<Tuner/Timer Section (Fig. 6) >
. Display Panel
A) CLOCK Indicator
B) CANCEL Indicator
C) TIMER ON Indicator
D) TIMER OFF Indicator
E) STEREO indicator
F) MEMORY Indicator
G) Station Number Display
H) ST/MUTE Indicator
1) TUNED Indicator
¢) Frequency/Time Dispiay
K) MW Indicator :
L) LW indicator
M) FM1/FM2/FM3 indicators
- STATION Buttons (1 ~ 6)
. Broadcast Band Select Buttons
. ST/MONO Button
PLAYBACK ONLY
RECORD/PLAYBACK
- DECK 2 STOP/EJECT Button
. DECK 2 PAUSE Button
. DECK 2 PLAY Button
. DECK 2 RECORD Button
- DECK 1 PAUSE Button
Remote Control Unit (Fig. 8)
1.
2.
< Amplifier Section >
3.
4.
5.
13.
14,
15.
MUTING Button
<CD Section >
6.
7.
8.
9.
FBACK Button
FFWD Button
PLAY/PAUSE Button
STOP Button
< TUNER Section >
10. MW/LW Band Select Button
11. FM-1/2/3 Band Select Button
12. UP and DOWN TUNING Buttons
Fig. 8
a) REM-MS2 Remote Control
Basic Adjustments And Indicators
Refer to Fig. 5 and Fig. 6, to locate the controls and indicators.
8. SURROUND Button and Indicator
When this button is pressed and the indicator lights, the sound will
seem more expansive.
Connect surround speakers to create the atmosphere of a concert
~ When surround speakers are connected, sound is produced
from the surround speakers even if the SURROUND
indicator
is off.
11. TIMER Buttons
ON Button: To set the on time, press this button, then press the
MEMORY button within 5 seconds.
OFF Button: To set the off time, press this button, then press the
MEMORY button within 5 seconds.
CANCEL
Button: Press this button to cance! the timer.
14. Display Panel
=) STEREO Indicator
This indicator lights when the ST/MONO button is set to ST and
an FM stereo broadcast is received.
G) Station Number Dispiay
When a station is memorized, or when a memorized station is
recalled, the number
of the memorized
station's button ap-
pears in this display (see "Presetting Stations").
—
When the UP or DOWN button is pressed, this display turns
off.
H) ST/MUTE Indicator
This indicator lights when the FM-1/2/3 Band Select button is
pressed and the ST/MONO button is set to ST.
1) TUNED Indicator
This indicator lights when a station is tuned in. (it flashes when
the signal is weak, and in some cases it may not light at all.)
17. ST/MONO Button
a) ST (ST/MUTE indicator on):
Stereo broadcast are heard
in stereo. Monaural
broadcasts
are heard in mono.
interstation
noise
is suppressed
during
tuning.
MONO (ST/MUTE indicator off):
Select this mode to receive weak FM stations. Reception will
be improved, but the sound will be monaural. Interstation noise
will not be suppressed during tuning.
NOTE:
The ST/MUTE function affects FM reception only.
b
~~
Listening To The Radio
Refer to the "QUICK OPERATION"
section.
Automatic/Manual Tuning
1. Press the MW/LW
or FM-1/2/3 Band Select button to select the
desired broadcast band.
'
2. Tune in a station.
Automatic Tuning:
Press and hold down the UP or DOWN
button to change the fre-
quency. Release the button.
— The frequency changes continuously until a station is tuned
in.
~
The frequency stops changing if the button is pressed
again
before a station is tuned in.
Manual Tuning:
Press and release the UP or DOWN button repeatedly
to change
the frequency in small steps.
~ The frequency changes in steps of 9kHz for the MW band,
1kHz
for the LW band, and 0.05MHz for the FM band.
NOTE:
When the end of the broadcast band is reached during
tuning, the scan
function will skip to the opposite end of the band.