First Flight - GRAUPNER PITTS S12 1400 Montageanleitung

78 Rear cabane doubler
79 Elevator
80 Wheel axle doubler
81 Outer right wheel spat shell
82 Outer left wheel spat shell
83 Inside right wheel spat shell
84 Inside left wheel spat shell
84 Locating ring
85 Collet
86 Brass tubular rivet
87 Tailwheel
88 Undercarriage leg fairing
89 Cowl former
90 Cowl stringer
91 Cowl reinforcing former
92 Cowl shell
93 Right oil cooler shell
94 Left oil cooler shell
95 Rigging doubler
96 Strut holder
97 Clevis opener
98 Black ball-link
99 Natural ball-link
100 Aileron link rod horn
101 Plastic clevis
102 Motor mount
103 Motor mount retaining screw
104 Grommet
105 Spinner locating plate
106 Spinner backplate
107 Spinner former
108 Spinner former
109 Spinner former
110 Spinner cap
111 Propeller hub
112 CFRP propeller spacer
113 Propeller hub
114 Velcro tape
115 Canopy frame
116 Instrument panel support
117 Instrument panel
118 Pilot's head
119 Canopy
Numbers of the laser-cut parts
Model set-up
Control surface travels
Elevator
Rudder
Ailerons
Centre of Gravity: 60 - 65 mm aft of the bottom wing root leading edge.

First flight:

73
GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY
Keine Haftung für Druckfehler. Technische Änderungen vorbehalten!
ID# 0057887
2
2
2
1
1
1
1
8
1
1
1
2
1
1
1
2
1
1
4
4
1
2
2
4
4
2
3
6
2
1
1
1
1
1
1
1
1
1
1
1
1
2
1
100 mm up, 100 mm down
110 mm right, 110 mm left
55 mm up, 55 mm down
Charge the batteries, check all the model's working systems, and carry
out a range check. Wait for a day with as little air movement as possible
(flat calm is best). Trim the model out and take your time to become
accustomed to its handling, before gradually exploring its aerobatic
Birch Laser-cut, 3 mm thick
Depron® Laser-cut, 6 mm thick
Birch Laser-cut, 3 mm thick
Depron® Vac.-moulded, 3 mm thick
Depron® Vac.-moulded, 3 mm thick
Depron® Vac.-moulded, 3 mm thick
Depron® Vac.-moulded, 3 mm thick
Birch Laser-cut, 3 mm thick
Brass 2.1 Ø x 6.0 mm
Brass 2 Ø x 0.2 x 15 mm
- 15 mm Ø
Depron® Laser-cut, 3 mm thick
Depron® Laser-cut, 6 mm thick
Depron® Laser-cut, 6 mm thick
Depron® Laser-cut, 6 mm thick
Depron® Vac.-moulded, 3 mm thick
Depron® Vac.-moulded, 3 mm thick
Depron® Vac.-moulded, 3 mm thick
Beech Laser-cut, 1 mm thick
Birch Laser-cut, 3 mm thick
Beech Laser-cut, 2 mm thick
Plastic Inj. moulded
Plastic Inj. moulded
Beech Laser-cut, 2 mm thick
Plastic Inj. moulded
Beech Laser-cut, 2 mm thick
Steel M3 x 16 mm, socket-head
Rubber 7 x 4 x 3 mm
Beech Laser-cut, 2 mm thick
Beech Laser-cut, 2 mm thick
Beech Laser-cut, 1 mm thick
Beech Laser-cut, 1 mm thick
Beech Laser-cut, 1 mm thick
Depron® Vac.-moulded, 6 mm thick
Order No. 7690.4 Not included in the kit
Order No. 197.625 Not included in the kit
Order No. 6060.10 Not included in the kit
Order No. 3368.1 Not included in the kit
Depron® Laser-cut, 3 mm thick
Depron® Laser-cut, 3 mm thick
Depron® Laser-cut, 3 mm thick
Depron® Laser-cut, 3 mm thick
ABS Vac.-moulded, 0.5 mm thick
04/2007