Klein Tools CL2300A Bedienungsanleitung Seite 2

ENGLISH
CL2300A
Instruction Manual
GENERAL SPECIFICATIONS
The Klein Tools CL2300A is a True RMS, auto-ranging clamp meter. It measures
AC / DC voltage, AC / DC current, resistance, capacitance, frequency, duty cycle,
and temperature. It can also test non-contact voltage, diodes, and continuity.
• Operating Altitude: 2,000 m (6,562 ft.)
• Humidity: 80% max
• Operating Temperature: 0° to 45°C (32° to 113°F)
• Storage Temperature: 0° to 60°C (32° to 140°F)
• Accuracy Temperature: 18° to 28°C (64° to 82°F)
• Temperature Coef cient: 0.1*(specified accuracy) / °C
• Dimensions: 194 x 65 x 35 mm (7.65" x 2.56" x 1.375")
• Weight: 337 g (11.9 oz.)
• Calibration: Accurate for one year
• Accuracy: ± (% of reading + # of least significant digits)
• Ingress Protection: IP42 Certified
• Drop Protection: 2 m (6.6 ft.)
• Safety Rating: CAT III 1000V, CAT IV 600V
• Electromagnetic Environment: EN61326-1:2013 This equipment
meets requirements for use in basic and controlled electromagnetic
environments like residential properties, business premises, and
light-industrial locations.
Specifications subject to change.
WARNINGS
To ensure safe operation and service of the tester, follow these instructions.
Failure to observe these warnings can result in severe injury or death.
• Before each use, verify meter operation by measuring
a known voltage or current.
• Never use the meter on a circuit with voltages that exceed the
category based rating of this meter.
• Do not use the meter during electrical storms, or in wet weather.
• Do not use the meter or test leads if they appear to be damaged.
• Ensure meter leads are fully seated, and keep fingers away from
the metal probe contacts when making measurements.
• Do not open the meter to replace batteries while the probes
are connected.
• Use caution when working with voltages above 60V DC,
or 25V AC RMS. Such voltages pose a shock hazard.
• To avoid false readings that can lead to electrical shock,
replace batteries if a low battery indicator appears.
• Unless measuring voltage or current, shut off and lock out
power before measuring resistance or capacitance.
• Always adhere to local and national safety codes. Use individual
protective equipment to prevent shock and arc blast injury where
hazardous live conductors are exposed.
SYMBOLS
AC Alternating Current Warning or Caution
DC Direct Current Dangerous levels
DC/AC Voltage or Current Double Insulated Class II
Equipment is safe for
Ground
connection and disconnection
AC Source to live conductors
FEATURE DETAILS
1
B
E
8 2300A
J
L
F
G
D
H
I
C
4
K
A
A. Use CAT IV rated leads or higher.
DO NOT attempt to measure more than 1000V DC or 750V AC or 2000µA.
B. Keep hands below line when measuring high current levels.
C. Auto Power-Off (Apo)
• Device will power off after 30 minutes non-use.
• Turn the dial or press a button to wake.
• Disabled during Max / Min function.
• Holding Select button while turning on disables Auto Power-Off.
D. Select Functionality Button
• Switch between AC and DC.
• Switch between , and .
• Press for 2 seconds to switch between AC, frequency, and duty cycle.
• Press for 2 seconds to zero the display (DC clamp current only).
• Switch between ˚F and ˚C.
E. Hold / Backlight / Worklight
• Press to hold the current input on the display.
• Press again to return to live reading.
• Press for 2 seconds to enable / disable lights.
• Using lights drains the battery significantly.
F. Auto / Manual Range
• Press repeatedly to cycle through manual ranges.
• Press for 2 seconds to return to auto ranging mode.
AT
• is displayed on LCD only during auto ranging mode.
G. Max / Min Hold
• Press to enter Max / Min mode; the largest and smallest values
will be saved while in this mode.
• Press repeatedly to alternate between the maximum and minimum readings.
• Press for 2 seconds to return to live reading and clear the stored
maximum and minimum values.
H. I. Battery Replacement
• When indicator is displayed on the LCD, batteries must
be replaced.
• Remove the back screw and replace 2 x AAA batteries.
J. Magnetic Back
• Attach instrument to metal for hands-free use.
K. Bar Graph
• The bar graph shows an approximate analog representation
of a measurement.
• The bar graph responds much faster than the digital display.
• The scale of the bar graph is zero to the maximum reading of
the selected range.
L. Temperature Adjustment
• Remove battery cover.
• Place temperature probe in distilled
water with stirred crushed ice
(a standard for 0°C and 32°F).
• Use a fine tip screwdriver to adjust
the screw recessed in the top left
corner of the battery cavity as shown
until the display reads 0°C or 32°F.
FUNCTION INSTRUCTIONS
2300A
9
1
2
5
7
6
3
AC/DC Current (large): < 600A
1.
Features: PRESS
HOLD RANGE MAX/MIN ZERO (DC)
PRESS
AC
DC
• Center wire in guides for best accuracy.
• Opposing currents cancel; use line-splitter when necessary*.
AC / DC Current (small): < 2000µA
2.
Features:
PRESS
HOLD RANGE MAX/MIN
PRESS
AC
DC
• Select AC or DC current source.
• Current above 2000µA will damage instrument.
* For North America only.
AC / DC Voltage: < 750V AC or 1000V DC
3.
PRESS
Features: HOLD RANGE MAX/MIN
PRESS
AC
DC
• Select AC or DC voltage source.
4. Frequency (Hz) / Duty Cycle (See Feature Details)
Features:
HOLD
PRESS &
HOLD
SELECT
Hz/Duty/Zero
• Select , ,or setting.
• Frequencies out of range will display "0.000Hz".
Capacitance: < 6000µF
5.
Features: HOLD
• Safely discharge capacitor before measurement.
• Reading may take up to 60 seconds for large capacitors.
Resistance: < 60M
6.
Features: HOLD RANGE MAX/MIN
PRESS
TO SELECT TO SELECT
Resistance Resistance
Continuity Continuity Continuity
Diode Diode
• DO NOT measure resistance on a live circuit.
7. Diode / Continuity
PRESS
TO SELECT TO SELECT
Resistance Resistance
Continuity Continuity Continuity
Diode Diode
Diode / Continuity Features Continued on Reverse