Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Battery model GBA 18V...
LED
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Battery model ProCORE18V...
LED
5 × continuous green light
4 × continuous green light
3 × continuous green light
2 × continuous green light
1 × continuous green light
1 × flashing green light
Recommendations for Optimal Handling of the
Battery
Protect the battery against moisture and water.
Only store the battery within a temperature range of −20 to
50 °C. Do not leave the battery in your car in the summer, for
example.
Occasionally clean the ventilation slots on the battery using a
soft brush that is clean and dry.
A significantly reduced operating time after charging indic-
ates that the battery has deteriorated and must be replaced.
Follow the instructions on correct disposal.
Assembly
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Inserting/replacing the bandsaw blade
Wear protective gloves when fitting and changing the
u
bandsaw blade. Danger of injury when touching the
bandsaw blade.
Always wear safety goggles. Safety goggles reduce the
u
risk of injury.
Selecting a bandsaw blade
An overview of recommended bandsaw blades can be found
at the end of these instructions.
Bosch Power Tools
Fitting the Bandsaw Blade (see figures A−F)
Swivel the pre-tension lever (12) as far as it will go in
the
up the cover (15).
Capacity
Guide the bandsaw blade (11) bit by bit into the saw blade
60–100 %
guides (16). The rear end of the saw blade must touch the
bearings in the bottom part of the saw blade guides (16).
30–60 %
Guide the bandsaw blade (11) bit by bit around the two
5–30 %
rollers (17).
0–5 %
To tension the bandsaw blade (11), swivel the pre-tension
lever (12) in the direction as far as it will go. Check
whether the bandsaw blade (11) is running correctly around
both rollers (17).
Close the cover (15) and lock it with the locking clips (9).
Check that the bandsaw blade (11) is seated cor-
u
Capacity
rectly. Briefly switch the power tool on and off several
80–100 %
times. If the bandsaw blade is not mounted correctly, it
60–80 %
can come undone and injure you.
40–60 %
Removing the Bandsaw Blade
20–40 %
Swivel the pre-tension lever (12) as far as it will go in
5–20 %
the
0–5 %
up the cover (15).
Pull the bandsaw blade (11) out of the saw blade
guides (16) and out of the two rollers (17).
Adjusting the Guide (see figure G)
Always use the guide (10) to ensure safe and precise cuts.
Adjust the length of the guide to the relevant cut.
To do this, loosen the two screws (18) on the guide using
the hex key (8). Pull the guide out (10) as far as required.
Re-tighten the two screws (18) using the hex key (8).
In order to transport or store the power tool, you can push
back the guide (10) as far as it will go.
Dust/Chip Extraction
Dust from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one's
health. Touching or breathing-in the dust can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
Certain dust, such as oak or beech dust, is considered carci-
nogenic, especially in connection with wood-treatment ad-
ditives (chromate, wood preservative). Materials containing
asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the ma-
terials to be worked.
Avoid dust accumulation at the workplace. Dust can
u
easily ignite.
direction. Release the two locking clips (9) and lift
direction. Release the two locking clips (9) and lift
1 609 92A 8RW | (16.11.2023)
English | 17
Werbung
