Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Shorting the battery terminals together may cause burns
or a fire.
Under abusive conditions, liquid may be ejected from
u
the battery; avoid contact. If contact accidentally oc-
curs, flush with water. If liquid contacts eyes, addi-
tionally seek medical help. Liquid ejected from the bat-
tery may cause irritation or burns.
Service
Have your power tool serviced by a qualified repair
u
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Safety Instructions for Band Saws
Hold power tool by insulated gripping surfaces, when
u
performing an operation where the cutting accessory
may contact hidden wiring. Cutting accessories contact-
ing a "live" wire may make exposed metal parts of the
power tool "live" and could give the operator an electric
shock.
Use clamps or another practical way to secure and
u
support the workpiece to a stable platform. Holding
the work by your hand or against the body leaves it un-
stable and may lead to loss of control.
Keep hands away from the sawing area. Do not reach
u
under the workpiece. Contact with the saw blade can
lead to injuries.
Only bring the power tool into contact with the work-
u
piece when switched on. Otherwise there is danger of
kickback if the cutting tool jams in the workpiece.
When the cut is completed, switch off the power tool
u
and then pull the band saw blade out of the cut only
after it has come to a standstill. In this manner you can
avoid kickback and can place down the power tool se-
curely.
Use only undamaged band-saw blades that are in per-
u
fect condition. Bent or dull band-saw blades can break
or lead to kickback.
Keep lubricants or oil away from the band-saw blade.
u
Completely wipe off excess oil before cutting. Other-
wise, the band-saw blade can slip.
Do not apply strong pressure to the band-saw blade
u
during operation. Excessive pressure can cause the
band-saw blade to slip or break. This poses a risk of in-
jury.
After switching off, do not stop the band-saw blade by
u
applying lateral pressure to it. The band-saw blade can
become damaged, break or lead to kickback.
Do not touch the band-saw blade directly after the
u
working process until after it has cooled down. The
band-saw blade becomes very hot while working.
Hold the power tool firmly with both hands and make
u
sure you have a stable footing. The power tool can be
more securely guided with both hands.
Always wait until the power tool has come to a com-
u
plete stop before placing it down. The application tool
can jam and cause you to lose control of the power tool.
Bosch Power Tools
In case of damage and improper use of the battery, va-
u
pours may be emitted. The battery can set alight or ex-
plode. Ensure the area is well ventilated and seek medical
attention should you experience any adverse effects. The
vapours may irritate the respiratory system.
Do not open the battery. There is a risk of short-circuit-
u
ing.
The battery can be damaged by pointed objects such
u
as nails or screwdrivers or by force applied externally.
An internal short circuit may occur, causing the battery to
burn, smoke, explode or overheat.
Only use the battery in the manufacturer's products.
u
This is the only way in which you can protect the battery
against dangerous overload.
Protect the battery against heat, e.g. against
continuous intense sunlight, fire, dirt, water
and moisture. There is a risk of explosion and
short-circuiting.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is intended for sawing plastic, metal and rub-
ber while resting firmly against the material being sawn. It is
suitable for straight cuts. The saw blade recommendations
are to be observed.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Auxiliary handle (insulated gripping surface)
(2) Rechargeable battery release button
a)
(3) Rechargeable battery
(4) Thumbwheel for preselecting the blade speed
(5) On/off switch
(6) Lock-off function for On/Off switch
(7) Handle (insulated gripping surface)
(8) Hex key
(9) Locking clip for cover
(10) Material guide
(11) Bandsaw blade
(12) Lever for bandsaw blade pre-tension
(13) Hanging hook
(14) Worklight
English | 15
a)
1 609 92A 8RW | (16.11.2023)
Werbung
