Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Installing the battery pack (Fig. 3b)
Press the pushlock button (Fig. 3b/Item C) of the
rechargeable battery and push the rechargeable
battery into the mount provided. Make sure that
the pushlock button engages properly! To remove
the battery, proceed in reverse order!
Charging the battery (Fig. 4)
1. Take the battery pack out of the equipment.
Press the push/lock button to do this.
2. Check that your mains voltage matches the
voltage specifi ed on the rating plate of the
battery charger. Insert the power plug of the
charger into the socket outlet. The green LED
will then begin to fl ash.
3. Insert the battery pack into the charger.
4. In the section entitled „Charger indicator"
there is a table with an explanation of the LED
display on the charger.
The battery pack can heat up slightly during char-
ging. This is normal.
If the battery pack fails to charge, please check:
•
whether there is a voltage at the mains power
socket;
•
whether there is good contact at the charging
contacts.
If the battery pack still fails to charge, please send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
Battery capacity indicator (Fig. 4a)
Press the battery capacity indicator switch (item
A). The battery capacity indicator (item B) shows
the charge status of the battery using 3 LEDs.
Anl_GC-CH_18-50_Li_SPK7_Globus.indb 17
Anl_GC-CH_18-50_Li_SPK7_Globus.indb 17
GB
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
6. Operation
Switching ON/OFF.
The hedge trimmer is equipped with a two-han-
ded safety switch. It works only when the switch
on the steady grip (Fig. 6/Item 3a) is pressed with
one hand and the switch (Fig. 3b/Item 4a) on the
handle is pressed with the other hand. If either
switch is released, the cutters will stop moving.
Please watch out for the cutters as they slow
down to a standstill.
Notes for use
•
A hedge trimmer can be used to cut shrubs
and bushes as well as hedges.
•
To obtain the best cutting results, hold the
hedge trimmer so that the cutter teeth are
at an angle of approx. 15° in relation to the
hedge (see Fig. 5).
•
The twin-bladed cutters rotate in opposite
directions, thus enabling cutting in both direc-
tions (see Fig. 6).
•
To ensure that you cut the hedge to a level
height, we recommend tying a guide line of
string or similar along the hedge. Cut off all
branches that protrude beyond the guide line
(see Fig. 7).
Warning! Be particularly attentive when cutting
along the guide line. Do not cut through the guide
line. This could get entangled in the blades and
lead to injuries or damage to property.
•
Cut the sides of the hedge with curve-shaped
movements from the bottom up (see Figu-
re 8).
- 17 -
02.08.2023 14:22:33
02.08.2023 14:22:33
Werbung
