EINHELL GC-CH 18/50 Li Originalbetriebsanleitung Seite 16

4. Technical data
Rated voltage ..........................................18 V d.c.
Cutter rail length ..................................... 550 mm
Cutting length ......................................... 500 mm
Tooth spacing ........................................... 17 mm
Cuts/min. ..................................................... 2400
Sound pressure level L
Sound power level L
WA
Uncertainty K / K .................................... 3 dB
pA WA
Sound power level guaranteed L
Vibrations a .........................................≤ 2.5 m/s
h
Uncertainty K ..........................................1.5 m/s
Weight: .......................................................2.2 kg
Power-X-Change lithium-ion rechargeable
battery
Voltage: .................................................. 18 V DC
Capacity: ................................................... 2.5 Ah
Number of cells: ............................................... 5
Important!
The equipment is allowed to be used only with the
lithium-ion rechargeable batteries of the Power
X-Change series!
Charging unit Power-X-Change 18V
Mains voltage ................... 200-250 V ~ 50-60 Hz
Output
Rated voltage ........................................ 20 V d. c.
Rated current ........................................ 3000 mA
Protection class ........................................... II /
Important!
The charging unit is allowed to be used only for
the lithium-ion batteries of the Power X-Change
series!
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
The stated vibration emission levels and stated
noise emission values were measured in ac-
cordance with a set of standardized criteria and
can be used to compare one power tool with
another.
The stated vibration emission levels and stated
noise emission values can also be used to make
an initial assessment of exposure.
Anl_GC-CH_18-50_Li_SPK7_Globus.indb 16 Anl_GC-CH_18-50_Li_SPK7_Globus.indb 16
....................... 71 dB(A)
pA
........................... 91 dB(A)
........ 96 dB(A)
WA
2
2
- 16 -
GB
Warning:
The vibration and noise emission levels may vary
from the level specifi ed during actual use, depen-
ding on the way in which the power tool is used,
especially the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
Limit the operating time!
All stages of the operating cycle must be conside-
red (for example, times in which the electric tools
are switched off and times in which the tool is
switched on but operates without load).
5. Before starting the equipment
Rotatable handle
The hedge trimmer is fi tted with a rotatable rear
handle. It can be rotated 90° to the left and right.
To do this, pull the slide (Fig. 3a / item 7) in the
direction of the arrow and rotate the handle.
To return the handle to its original position, pull
the slide (Fig. 3a / item 7) back in the direction of
the arrow. The handle should be rotated through
90° when performing vertical cuts.
02.08.2023 14:22:33 02.08.2023 14:22:33