Atlas Copco EP6XS HR10 Sicherheitshinweise Seite 4

Safety Information
tive (2011/65/EU). Lead metal will not leak or mutate from
the product during normal use and the concentration of lead
metal in the complete product is well below the applicable
threshold limit. Please consider local requirements on the dis-
posal of lead at product end of life.
UK DECLARATION OF CONFORMITY
We, Atlas Copco Industrial Technique AB,
SE-105 23 STOCKHOLM SWEDEN, declare
under our sole responsibility that the product
(with name, type and serial number, see front
page) is in conformity with the following UK
Regulation(s):
S.I. 2008/1597
Designated Standards applied:
EN ISO 11148-6:2012
Authorities can request relevant technical information from:
Aleksandra Duric, Product Compliance Manager, Atlas
Copco Industrial Technique AB, SE-105 23 Stockholm Swe-
den
Stockholm, 1 September 2023
Håkan Andersson, Managing Director
Signature of issuer
Authorised Representative UK
James McAllister, General Manager
Atlas Copco Ltd
Swallowdale Lane
Hemel Hempstead
Hertfordshire HP2 7EA
Safety
WARNING Risk of Property Damage or Severe In-
jury
Ensure that you read, understand and follow all instruc-
tions before operating the tool. Failure to follow all the
instructions may result in electric shock, fire, property
damage and/or severe bodily injury.
Read all Safety Information delivered together with
►
the different parts of the system.
Read all Product Instructions for installation, opera-
►
tion and maintenance of the different parts of the
system.
Read all locally legislated safety regulations regard-
►
ing the system and parts thereof.
Save all Safety Information and instructions for fu-
►
ture reference.
4 © Atlas Copco Industrial Technique AB - 9836 2377 00
Statement of use
This product is designed for installing and removing threaded
fasteners in wood, metal or plastic.
No other use permitted. For professional use only.
Product specific instructions
Installation of vibrating tools
We recommend using a minimum length of 300 mm (12") of
flexible hose for compressed air between a vibrating tool and
the quick-action coupling.
General safety instructions
To reduce risk of injury, everyone using, installing, repairing,
maintaining, changing accessories on, or working near this
tool must read and understand these instructions before per-
forming any such task.
Our goal is to produce tools that help you work safely and ef-
ficiently. The most important safety device for this or any tool
is YOU. Your care and good judgment are the best protection
against injury. All possible hazards cannot be covered here,
but we have tried to highlight some of the important ones.
• Only qualified and trained operators should install, adjust
or use this power tool.
• This tool and its accessories must not be modified in any
way.
• Do not use this tool if it has been damaged.
• If the rated speed, operating pressure or hazard warning
signs on the tool cease to be legible or become detached,
replace without delay. For additional safety information
consult:
Other documents and information packed with this
tool.
• Your employer, union and / or trade association.
• "Safety Code for Portable Air Tools" (ANSI
B186.1), available at the time of printing from
Global Engineering Documents at http://
global.ihs.com/ , or call 1 800 854 7179. In case of
difficulty in obtaining ANSI standards, contact ANSI
via http://www.ansi.org/
• Further occupational health and safety information
can be obtained from the following web sites:
• http://www.osha.gov (USA)
• https://osha.europa.eu/ (Europe)
Air supply and connection hazards
• Air under pressure can cause severe injury.
• Always shut off air supply, drain hose of air pressure and
disconnect tool from air supply when not in use, before
changing accessories or when making repairs.
• Never direct air at yourself or anyone else.
• Whipping hoses can cause severe injury. Always check
for damaged or loose hoses and fittings.
• Do not use quick disconnect couplings at tool. See in-
structions for correct set up.
EP6XS HR10