BERGNER BG-50038-WH Bedienungsanleitung Seite 12

Note: Can run a water-only cycle to stabilize the boiler temperature and avoid the smell of burnt
coffee.
PRODUCING STEAM TO HEAT LIQUIDS
The steam wand (without the frothing device) can be used to make hot beverages like drinking
chocolate, water or tea.
Method:
1. Open the top cover, remove the detachable tank and fill it with desired water, the water level should
not exceed the "MAX" mark in the tank. Then place the tank into the appliance properly.
2. Replace the top cover, then connecting the appliance to power supply source.
3.Press the ON/OFF switch to the "—" position, the lamp in itself is illuminated.
4. Make sure the coffee/steam selector on the "O" position, turn the pump control switch to the "—"
position, the pump will pump water, when there is water flowing out, close the pump immediately,
pressing the coffee/steam selector to the "—" position and waiting for a moment, the appliance begins
to be heated until the lamp in coffee/steam switch is illuminated, it shows the heating is finish.
5. Remove the frothing device from the steam wand.
6. Dip the steam wand into the liquid to be heated. Turn the steam control knob in anti-clockwise slowly
to start making steam.
7. When the required temperature is reached, you can turn the steam control knob to OFF position.
8. Press the ON/OFF switch to the "O" position to cut off the power source.
AUTOMATIC POWER OFF FUNCTION
After 25 minutes of turning on the power switch, the unit will power off automatically.
CLEAN AND MAINTENANCE:
1. Cut off power source and let the coffee maker cool down completely before cleaning.
2. Clean housing of coffee maker with moisture-proof sponge often and clean water tank, drip tray and
removable shelf regularly then dry them.
Note: Do not clean with alcohol or solvent cleanser. Never immerse the housing in water for cleaning.
3. Detach the metal funnel through turn it clockwise, get rid of coffee residue inside, then you can
clean it with cleanser, but at last you must rinse with clear water.
4. Clean all the attachments in the water and dry thoroughly.
CLEANING MINERAL DEPOSITS
1. To make sure your coffee maker operating efficiently, internal piping is cleanly and the peak flavor of
coffee, you should clean away the mineral deposits left every 2-3 months.
2.Fill the tank with water and descaler to the MAX level ( the scale of water and descaler is 4:1, the
detail refers to the instruction of descaler. Please use "household descaler", you can use the citric acid
(obtainable from chemist's or drug stores) instead of the descaler (the one hundred parts of water and
three parts of citric acid).
3.According to the program of pre-heating, put the metal funnel (no coffee powder in it) and carafe(jug)
in place. Brewing water per " PRE-HEATING".
4. Press the ON/OFF switch to "—" position, the lamp in itself will be illuminated, you should press the
pump control switch, maker sure the coffee/steam selector to the "O" position, when there is water
flowing out and close the pump, and waiting for a moment, the coffee maker begins to be heated.
5. When the lamp in pump control switch is illuminated, it shows the heating is finish. Pressing the
pump control switch to "—" position and make two cups coffee (about 2Oz). Then close the pump and
wait for 5s.
6. Press the coffee/steam selector to the "—" position, the indicator in the pump control switch will be
extinguished, waiting for until the indicator in the coffee/steam selector is illuminated. Make steam
for 2min by turning the steam control knob, then turn the steam control knob to OFF position to stop
making steam. Press the ON/OFF switch to the "O" position to stop the unit immediately, make the
descalers deposit in the unit at least 15 minutes.
7. Restart the unit and repeat the steps of 4-6 at least 3 times.
8. Then pressing the coffee/steam selector to "O" position, the lamp in pump control switch will be
illuminated, then press the pump control switch to "—" position to brew until no descaler is left.
12