Product Description And Specifications - Bosch PSB 500 RE Originalbetriebsanleitung

OBJ_BUCH-862-009.book Page 13 Tuesday, April 14, 2015 10:34 AM
 Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
 Always wait until the machine has come to a complete
stop before placing it down. The tool insert can jam and
lead to loss of control over the power tool.
 Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse
(ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should
be cut off and an appropriate plug fitted in its place by an
authorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Products sold in AUS and NZ only: Use a residual current
device (RCD) with a rated residual current of 30 mA or less.
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
Intended Use
The machine is intended for impact drilling in brick, concrete
and stone as well as for drilling in wood, metal and plastic. Ma-
chines with electronic control and right/left rotation are also
suitable for screwdriving.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Depth stop*
2 Front sleeve
3 Rear sleeve
4 Keyless chuck
5 Button for depth stop adjustment *
6 "Drilling/Impact Drilling" selector switch
7 Lock-on button for On/Off switch
8 Rotational direction switch
9 On/Off switch
10 Auxiliary handle (insulated gripping surface) *
11 Wing bolt for adjustment of auxiliary handle *
12 Extraction device with dust collector *
Technical Data
Impact Drill
Article number
Rated power input
Output power
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Bosch Power Tools
13 Dust collector*
14 Level indicator of the dust collector *
15 Handle (insulated gripping surface)
16 Release button for dust collector *
17 Filter element (Microfilter System) *
18 Rubber gasket for dust collector *
19 Dust protection ring*
20 Release button for extraction device *
21 Clamp for extraction device *
22 Locking latch for dust collector*
23 Universal bit holder*
24 Screwdriver bit*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-1.
Typically the A-weighted noise levels of the product are:
Sound pressure level 97 dB(A); Sound power level
108 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-1:
Drilling into metal: a =4.0 m/s
h
Impact drilling into concrete: a
Screwdriving without impact: a
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
PSB 500 RE PSB 500 RA
3 603 A27 0.. 3 603 A27 0..
W 500
W 260
English | 13
2 2
, K=1.5 m/s
2 2
=33 m/s , K=3.5 m/s
h
2 2
<2.5 m/s , K=1.5 m/s .
h
PSB 560 RE
3 603 A27 041
500 500
260 260
1 609 92A 18J | (14.4.15)