Herunterladen Diese Seite drucken

Teac V-770 Bedienungsanleitung Seite 7

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

from left to right, and downwards during
rewind as the tape moves from right to left.
The indicated numerals are not related to
time lapse and are not compatible with the
counter
readings of other cassette decks.
A typical
example
of using this display
in the conventional tape counter mode is to
first load a cassette and, before recording,
press
the
CLEAR
button
resetting
the
counter to "0000". Then note the counter
reading at the beginning of each piece of
music to facilitate
locating a particular
selection when you wish to play it back.
Using as a Tape-run-time Counter
Using the COUNTER MODE button, call up
the tape-run-time
mode;
a dot
appears
between
the 2nd and 3rd digit. In this
mode, tape travel is measured in increasing
minutes and seconds while the tape is
running at normal speed during recording
(including record muting) and playback.
Counting
stops
during
rewind
and
fast-
forward, This function can be used to
measure
the approximate
length of a re-
corded song or to make a calculated estima-
tion of how much tape is left.
"Visible" and "Invisible" Counters
Both counter modes are switchable at any
time, with the one selected appearing on the
display and the other functioning in mem-
ory. For example, when the conventional
tape counter is selected with the COUNTER
MODE
button, counting of the tape-run-
time also takes place and its reading can
be called up at any time by pressing the
COUNTER
MODE
button.
Pressing
the
CLEAR
button
resets only the
counter
whitch is visible. Both counters, "visible" and
"invisible" are reset when power is switched
off.
Tune
Blank
More than approx,
Tune
Blank_4 sec, needed
|
BD Direction of
Fastforward
Play
{NMI ORR e UU
Fastforward
Play
tape travel
Approx, 10 sec.
INTRO CHECK facility
INTRO CHECK Function
This feature makes searching for a specific
selection much easier.
1. Press the INTRO CHECK button.
2. The deck enters the fast forward mode
(CP 1 appears on the Multi Counter) to
search for the beginnings of selections,
When a selection is detected (CP 0 ap-
pears), the deck will play approximately
the first ten seconds of the recording and
then fast-forward to the beginning of
the next selection,
To cancel the INTRO CHECK function,
press the STOP button.
4. If STOP is not pressed, the INTRO
CHECK function is released when the
tape reaches the end,
oe
INTRO CHECK-CPS Function
Repeatedly pressing the CPS button during
the fast forward made, while the CP 1 is
displayed increases the CPS number. The
CPS function makes the deck skip to a se-
lected recording and enter the play mode
for ten seconds and then resume the INTRO
CHECK function,
(Pressing the CPS button during the play-
back in INTRO CHECK cancels the INTRO
CHECK
function.) To cancel the INTRO
CHECK-CPS function, press any of the trans-
port control buttons,
Notes:
Pressing
the
INTRO
CHECK
button
is
possible in any tape operation mode,
During intro check, if STOP, » , »» or
#<_is pressed, the intro check function
is canceled and the corresponding mode is
entered.
eFor the intro check function to work
properly, there must be a blank of at least
4 seconds or more between selections,
See
also: "Notes common
to INTRO
CHECK, CPS, COS",
CPS (Computomatic Program Search)
Function
CPS allows playback to start up to 15 tunes
ahead of or before the one being played.
This
function
is performed
by detecting
blank spaces of at least 4 seconds between
tunes, Blanks can be created using the REC
MUTE facility.
1, Press the CPS/CDS
button
repeatedly
until the number of tunes to be skipped
appears in the MULTI COUNTER (CP 1,
CP 2, ... CP 15), Refer to chart "How to
Select a Desired Tune Using CPS".
elf the displayed number exceeds the
required
one, press the COUNTER
CLEAR button and redo CPS setting,
How to Select a Desired Tune Using CPS
Ex.
See (1), To select the 3rd tune past the current tape position, select "CP 3".
(1)
Current tape position
(2)
In example (1), if "t'' is lessthan
Ahead | Before
4 seconds, it will not be counted
H
as
a blank
space.
Designate
|
"CP 2" instead of "CP 3" t
select the 3rd tune in this case.
(3
Current tape position
(4)
eS
CFS}
&
T
pees | Before

Werbung

loading