Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Sanders may coast for a short time after the trigger is released.
Be sure tool has come to a complete stop before setting it aside.
Sanders that do not come to a complete stop before setting aside can cause injury.
Backing pads that are worn, damaged, nicked, bent, warped or burred can cause the sanding disc to tear and burst.
Do not use backing pads that are worn, damaged, nicked, bent, warped or burred.
Sanding pads that burst can cause injury.
Modifications to the sander can effect tool performance and safety.
Do not modify the sander. Do not operate the sander if it has been modified or damaged. Periodically inspect sander for damage
and to ensure all safety markings are legible. Do not discard the safety instructions; give them to the operator. The user shall
contact the manufacturer to obtain replacement marking labels when necessary.
Damaged or modified sanders can cause injury.
The use of any accessory with this tool not provided or specified by Sioux Tools can perform unpredictably.
Use only accessories provided or specified by Sioux Tools. Only qualified and trained operators should install, adjust or use the
sanders.
Tools that perform unpredictably can cause injury.
Operators and maintenance personnel shall be physically able to handle the bulk, mass and power of the tool.
Hold the tool correctly; be ready to counteract normal or sudden movements and have both hands available.Release the start-
and-stop device in the case of an interruption of the energy supply. Personal protective safety glasses shall be used; suitable
gloves and protective clothing are recommended. Inspect the backing pad before each use. Do not use if cracked or broken or
if it has been dropped. Never run the tool unless abrasive is applied to the workpiece. There is a risk of electrostatic discharge if
used on plastic and other non-conductive materials.
Potentially explosive atmospheres can cause by dust and fumes resulting from sanding. Always use dust extraction or suppression
systems which are suitable for the material being processed.
Be aware of workplace hazards.
Slips, trips and falls are major causes of workplace injury. Be aware of slippery surfaces caused by use of the tool and also
of trip hazards caused by the air line. Ensure that there are no electrical cables, gas pipes, etc., which can cause a hazard if
damaged by use of the tool.
Workplace hazards can cause injury.
When disposing of a tool, do it in a way that does not harm personnel or the environment.
INTENDED USE
This tool is designed for the purpose of cleaning or sanding of a variety of materials typically metal, wood, plastic materials, etc. The dual rotary orbital action
reduces the amount of abrasive grinding marks and hence is primarily a finishing sanding tool. It can be used with a variety of grades of 150mm (6" diameter)
abrasive discs which according to pad fitted to the tool, can be self-adhesive or Velcro attached. Do not use the tool for any other purpose to that for which it
has been designed and use only abrasive discs as described. Do not modify the tool for any other use or for its use as a sander without first consulting the
manufacturer or its authorized representative.
AIR SUPPLY
The efficiency and life of this tool depend on the proper supply of clean, dry air at a maximum of 90 PSI. The use of an airline filter, pressure regulator, and
lubricator is recommended. Before connecting to tools, blow out the airline to remove water and dirt that may have accumulated.
HOSE AND HOSE CONNECTIONS
The air supply hose recommended is 3/8" (10mm) I.D. If an extension hose is necessary, use 1/2" (13mm) ID hose with couplings not less than 3/8" (10mm)
I.D. The tool inlet thread is 1/4" NPT.
LUBRICATION
All models may operate without airline lubrication. However, operating the tool without airline lubrication may reduce tool performance and vane life.
If an airline lubrication is not used, it is recommended that the tool be oiled daily before use to improve performance. Add 2-4 drops of air motor oil and run the
tool for 10-20 seconds to distribute oil through the tool.
For maximum performance and tool life, an air line lubricator, set to deliver 2 drops per minute, is recommended. SIOUX No. 288 Air Motor Oil is
recommended.
Do not over lubricate because excess oil may contaminate the surface being sanded.
For Angle Head
Lubricate the angle head assembly with 2 shots of SIOUX #1232 grease every 8 working hours.
MAINTENANCE
Water, dust and other airline contaminants can cause rust and vane sticking. For long periods between tool use, flush the tool with a few drops of oil and run
for 10 seconds. This will help remove contaminants and reduce the formation of rust.
OPERATION
The tool is equipped with a locking type lever in order to prevent accidental start-up.
The speed of the tool may be adjusted by turning the regulator lever located on the side of the body. The spindle lock can be set to provide either rotary or
orbital action. Slide the drive washer plate in until the point enters the recess in the pad mounting shaft for rotary action. The counterweight balance provides a
dual action which gives a smooth, swirl-free finish.
INSTALLING SANDING DISC (5/16-24UNF Thread)
•
Thread backing pad onto spindle.
•
Place sanding disc over spindle and seat against backing pad.
•
Thread disc retainer onto spindle and tighten
Form ZCE881
WARNING
Always remove the tool from the air supply be for installing or changing sanding discs!
3
Date 2023October3/A
Werbung
