Belt Tension Adjustment - Rebel Active Rba-1002 Bedienungsanleitung

MAINTENANCE
Regular maintenance is important for optimal performance and to reduce wear.
Inspect and properly tighten all parts each time the treadmill is used. Replace
any worn parts immediately.
WARNING Always unplug the treadmill before cleaning or any maintenance work.
• Regularly clean the treadmill and keep the running belt clean and dry.
• Use soft and slightly wet cloth to clean the exterior parts of the treadmill.
• To avoid damage to the console, do not clean it with wet cloth. Keep
liquids away from the console. Clean it only with a dry cloth.
• In order to better maintain the treadmill and extend its lifespan, it is
recommended that after 1,5 hour of use you turn off the treadmill and let
it rest for 10 minutes before continuing.
RUNNING BELT LUBRICATION
The friction between the running belt and the running deck has a great impact on
the lifespan and performance of the treadmill so the lubricating oil must be applied
regularly. Regularly inspect the running deck surface. If damaged, stop using the
treadmill and contact with an authorized service point for check-up and/or repair.
Before lubricating, clean the space between the deck and the belt to remove
any debris that may be trapped. Use a clean and dry cloth for that purpose.
To lubricate use only the lubricant that came with the treadmill or any other
dedicated lubricants.
The treadmill has been pre-lubricated between the running deck and the running belt.
It is recommended to apply the lubricant between the running deck and the
running belt on the following schedule or if you notice that the deck is dry. To
check if there is enough lubrication, simply reach between the belt and the deck
to verify if the lubrication is present. Do this regularly.
Use the following schedule to apply the lubricating oil:
• low-intensity exploitation (less than 3 hours per week) – once a year
• medium-intensity exploitation (3-5 hours per week) – once every six months
• high-intensity exploitation (more than 5 hours per week) – every 3 months
IMPORTANT! Make sure the treadmill is unplugged to prevent injury!
1. Lift the running belt slightly and squirt about 5 ml of the lubricant in a zig-
zag motion between the running belt and the running deck surface. Do
this in a few places on both sides of the running deck.
2. Once you have lubricated the deck, lower the running belt, stay off the
machine and turn it on. Run the belt at a slow speed for 5 to 10 minutes
so that the treadmill can spread the lubricant.
3. When all that is done, unplug the treadmill.
EN
32

BELT TENSION ADJUSTMENT

The running belt has been pre-tensioned. As the treadmill is used, the running
belt tends to stretch, and as a consequence it looses. If the running belt is too
loose, it will slip during running. If it is too tight, it may reduce the motor
performance and wear the guide rollers and the running belt.
WARNING Before making any adjustments, detach safety key and set the
power switch to the OFF position. After making the adjustments, install the
safety key and set the power switch to the ON position and run the treadmill
to see if the running belt tension is proper.
Adjustment screws are located on the left and on the right at the end of the
running deck.
TO TIGHTEN - Using a hex wrench provided,
turn both adjustment screws clockwise ¼ of a
turn.
TO LOOSEN - Using a hex wrench provided, turn both adjustment screws
anticlockwise ¼ of a turn.
After making the adjustments, run the treadmill and inspect for proper tension by
walking on the belt and making sure it is not slipping or hesitating with each step.
When the running belt is properly tightened, you should be able to lift each
edge of the belt 50 to 75 mm off the running deck.
WARNING Do not overtighten the running belt! It can decrease treadmill
performance, cause premature bearing wear and damage the running belt.
BELT CENTERING
Running belt should run as centrally and straight as possible. Some factors (such
as stress and load) can cause the running belt to shift near one side during use.
When that occurs, it is necessary to make adjustments.
WARNING Before making any adjustments, detach safety key and set the
power switch to the OFF position. After making the adjustments, install the
safety key and set the power switch to the ON position and run the treadmill
to see if the running belt has centered.
33
EN