AEG BUS 18 X Gebrauchsanleitung Seite 11

TECHNICAL DATA
Stroke rate under no-load ..............................................................
Lengths of stroke ............................................................................
Battery voltage ...............................................................................
Weight with battery .........................................................................
Typical weighted acceleration in the hand-arm area ......................
Typical A-weighted sound levels:
Sound pressure level (K = 3 dB(A)) ..............................................
Sound power level (K = 3 dB(A)) ..................................................
Measured values determined according to EN 60745.
SAFETY INSTRUCTIONS
Please pay attention to the safety instructions in the attached
leaflet!
Wear ear protectors. Exposure to noise can cause hearing loss.
Always wear goggles when using the machine. It is
recommended to wear gloves, sturdy non slipping shoes and
apron.
Sawdust and splinters must not be removed while the machine is
running.
The dust produced when using this tool may be harmful to
health. Do not inhale the dust. Wear a suitable dust protection
mask.
Do not use cracked or distorted saw blades.
Plunge cuts without pre-drilling a hole are possible with soft
materials (wood, light building materials for walls). Harder
materials (metals) must first be drilled with a hole corresponding
to the size of the saw blade.
Always place the guide shoe on the workpiece when sawing.
When working in walls ceiling, or floor, take care to avoid electric
cables and gas or waterpipes.
Do not dispose of used battery packs in the household refuse or
by burning them. AEG Distributors offer to retrieve old batteries
to protect our environment.
Do not store the battery pack together with metal objects (short
circuit risk).
No metal parts must be allowed to enter the battery section of
the charger (short circuit risk).
Use only System GBS chargers for charging System GBS
battery packs. Do not use battery packs from other systems.
Never break open battery packs and chargers and store only in
dry rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme
load or extreme temperatures. In case of contact with battery
acid wash it off immediately with soap and water. In case of eye
contact rinse thoroughly for at least 10 minutes and immediately
seek medical attention.
SPECIFIED CONDITIONS OF USE
This sabre saw cuts wood, plastic, and metal. It cuts curves and
can cut flush to a surface.
Do not use this product in any other way as stated for normal
use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is in
conformity with the following standards or standardized
documents. EN 60745, EN 55014-1, EN 55014-2, in accordance
with the regulations 98/37/EC, 89/336/EEC
Manager Product Development
13 ENGLISH
Volker Siegle
...................... 0-2500 min
-1
............................. 30 mm
............................. 18 V
............................ 4,1 kg
............................ 9,2 m/s
2
............................. 82 dB (A)
............................. 93 dB (A)
BATTERIES
Charge new battery packs before using.
Battery packs which have not been used for some time should
be recharged before use.
Temperatures in excess of 50
of the battery pack. Avoid extended exposure to heat or sunshine
(risk of overheating).
The contacts of chargers and battery packs must be kept clean.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all
times.
Use only AEG accessories and AEG spare parts. Should
components need to be replaced which have not been
described, please contact one of our AEG service agents (see
our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please
state the Article No. as well as the machine type printed on the
label and order the drawing at your local service agents or
directly at: AEG Elektrowerkzeuge, Max-Eyth-Straße 10,
D-71364 Winnenden, Germany.
SYMBOLS
Remove the battery pack before starting any
work on the machine.
Accessory - Not included in standard
equipment, available as an accessory.
Do not dispose of electric tools together with
household waste material! In observance of
European Directive 2002/96/EC on waste
electrical and electronic equipment and its
implementation in accordance with national
law, electric tools that have reached the end
of their life must be collected separately and
returned to an environmentally compatible
recycling facility.
C (120 F) reduce the performance
o o