FAAC 402 COMPACT Installationsanleitung Seite 5

402
PRELIMINARY PRECAUTIONS
Ensure that the structure of the gate
current regulations and that the movement
and without friction.
Make all necessary adjustments
stops before installing the automation
Installation must be carried
regulations.
INSTALLATION INSTRUCTIONS
I) Fix the rear mounting bracket
Fig. I and Table A.
N.B.: THESE DIMENSIONSARECRITICALTOENSURETHECORRECT
OPERATION OF THE SYSTEM.
2) Fix the ram to the rear mounting
3) Make the electrical connections
box (see relevant instructions).
4) Remove the bleed screw as shown in Fig. 3.
5) Maintaining the ram in the horizontal position, operate
ram five or six times ,checking
piston rod.
Should the piston rod tend to jerk, cycle the ram (air
N.B.:
bleeding) until the piston rod moves smoothly.
6) After bleeding, release the ram by inserting the key in the
manual release positioned
To unlock the ram turn the key anti-clockwise.
To lock turn the key clockwise.
7) With the ram unlocked, withdraw
its full extension and then reinsert it by 5 mm. (Fig. 5).
8) Fasten the front bracket
9) Close the gate, keep the ram in the horizontal
Locate and mark the position of the front bracket on the leaf
(Fig. 7).
10) Fix the front bracket to the leaf (Fig. 8).
N.B.: To prevent spatter from damaging
disconnect it from the
I I) Reconnect the piston rod to the front bracket
piston cover (Fig. 9).
12) Relock the manual release.
N.B.: All bolts should be greased
TECHNICAL SPECIFICATIONS
POWER SUPPLY(V)
POWER CONSUMPTION (W)
CURRENTCONSUMPTION (A)
MOTOR SPEED(g,'rnh)
TYERMAL OVERLOAD C UT-W (C)
PUMP FLOW RATE (l/min)
PISTON ROD SPEED (cnvsec)
EFF. PISTON ROD EXCURSION
MAX. THRUST(Kg)
DUTY CICLE
MAX. LEAF WIDTH (m)
HYDRAULIC STOP
OIL TYPE
OIL QUANTITY (l)
WEIGHT(kg)
ELECTRONIC CONTROL BOX
is in compliance
of the leaves iseven
including the fitting of gate
equipment.
out in compliance with current
to the gate post as shown in
bracket (Fig. 2).
to the electronic control
the smooth operation of the
beneath the cap (Fig. 4).
the piston rod by hand to
to the piston rod (Fig. 6).
position.
the rod during welding,
bracket.
and fit the
220±
1400
100
1.3
see Fig. 10
1.8
ONLY IN CLOSED POSITION
FAAC OIL XD 2m
09
6.5
402 MPS (included)
ADJUSTMENT OF THE ANTI-CRUSHING
The ram isequipped
with
ensures that movement
encountered or in the event of persons or objects being caught
in the path of the gate.
Red and green by-pass screws Wich are located
the unit are used to adjust the sensivity.
Closing thrust is set by the red screw.
Opening thrust isset by the green screw.
Clockwise to increase
Anti-clockwise to reduce
IMPORTANT NOTE:
Having completed
as shown in Fig. I I.
the
MAINTENANCE
For low to medium duty cycles inspection once a year issufficient.
For higher duty cycles inspection
only FAAC XD 220 oil should be used.
Regular inspection
5
ENGLISH
SAFETY DEVICE
with an anti-crushing safety device
will stop if an opposing
thrust.
thrust.
ADJUSTMENTS MUST REMAIN
LIMITS LAID DOWN BY ANY
LEGISLATION.
the adjustments, apply the protective
Fig. 11
BY PASS
E
Fig. 12
every 6 - 8 months isadvisable.
of the system is recommended.
which
force is
on the top ot
WITHIN THE
CURRENT
sticker
Fig. 13