Herunterladen Diese Seite drucken

Sony XDCAM PDBK-202 Bedienungsanleitung Seite 12

Vorschau ausblenden Andere Handbücher für XDCAM PDBK-202:

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 27
When the target device is the PDW-HR1
Item
V INPUT on the P1
VIDEO page of the
function menu
Sub-item TS i.LINK
MODE of setup menu
item 926
Sub-item PROGRAM
NUMBER of setup
menu item 926
When the target device is an XDS Series device
Item
F2: V INPUT on the
P1 INPUT page of the
function menu
Sub-item I/O MODE of
setup menu item 926
Sub-item TS MODE of
setup menu item 926
Sub-item PROGRAM
NUMBER of setup
menu item 926
• If you set V INPUT on the P1 VIDEO page of the
function menu to "DVB-ASI", then A1 INPUT to A4
INPUT on the P2 AUDIO page are also set automatically
to "DVB-ASI".
• Specifying a program number with sub-item
PROGRAM NUMBER of setup menu item 926 makes it
possible to select and receive a specified program from
DVB-ASI TS signals containing multiple multiplexed
programs.
To use metadata multiplexed into DVB-ASI
TS signals
Make the settings shown below, according to the type of
metadata.
12
System Configuration Examples
Setting
DVB-ASI
HDV: Set PROGRAM NUMBER to
"00100" (factory default
setting).
Manual: You can set PROGRAM
NUMBER to any program
number.
Note
This item does not appear on 720P
systems.
Set TS i.LINK MODE to "Manual",
and specify a program number (1 to
65535 (FFFFh)).
Setting
DVB-ASI
Set DVB-ASI input/output.
input [in]: Fixedly input mode
output [out]: Fixedly output mode
Select the TS mode. (59.94i/
29.97P/50i/25P mode only.)
HDV: HDV mode
Manual [manu]: Encoding rate
mode
Set TS MODE to "Manual" and
specify a program number
(decimal).
Metadata type
Setting
Timecode/user bits When the target device is the PDW-
HR1
INT/EXT/SDI switch: EXT or SDI
The internal timecode generator of the
target device synchronizes to the
timecode data contained in the TS
signal.
In the case of XDS Series device
When TCG in the TC page of the
function menu is set to "EXT" or "SDI",
the internal timecode generator
synchronizes to the timecode data
contained in the TS signal.
Essence mark
These are recorded automatically,
without any special settings.
In the case of the PDW-HR1, to check
for frames where essence marks are
set, display the chapter thumbnail
screen.
Clip name
Sub-item AUTO NAMING of setup
(PDW-HR1 only)
menu item 036: ext
The clip name in TS signals at the
recording start point is recorded. Even
if the clip name in the TS signals is
changed during recording, the change
to the clip name is not reflected.
UMID
This is recorded automatically, without
any special settings.
Note
Among the metadata types listed above, transmission of
essence mark information is given priority over
transmission of clip names. If there is too much essence
mark information to transmit, some time may be required
to transmit clip name information.
To output DVB-ASI TS signals
In the case of the PDW-HR1, put it into playback mode.
In the case of an XDS Series device, set I/O MODE of the
setup menu item 926 DVB-ASI SETTING to "output".
To multiplex metadata into DVB-ASI TS
output signals
Set sub-item META PACKET OUT of setup menu item
926 to "on".
During normal speed playback, metadata recorded on the
disc is transmitted at the same time as video and audio
data.
During playback of still images and variable speed
playback, only timecode is transmitted. Other metadata is
not transmitted.
Note
In the case of the PDW-HR1, if the sub-item TS i.LINK
MODE of the setup menu item 926 is set to "HDV",
metadata other than timecode data is not transmitted.

Werbung

loading