EINHELL TC-JS 85 Originalbetriebsanleitung Seite 18

•
The safety guard can be removed for carrying
out adjustments.
5.2 Changing the saw blade
(Figs. 3-4/Item 12)
Danger!
•
You can fit or replace saw blades without
using any other tools.
•
Pull out the mains plug before you fit or repla-
ce a saw blade.
•
Set the selector switch for pendulum action
(8) to position D (see Fig. 10).
•
The teeth of the saw blade are very sharp!
•
Remove the safety guard (15).
•
Press the blade holder (14) and insert the
saw blade (12) into the blade holder (14) as
far as the stop (Fig. 3). The teeth on the saw
blade must be pointing forwards.
•
Allow the saw blade holder (14) to slide back
into position. The saw blade (12) must sit in
the guide roller (10) (Fig. 4).
•
Check that the saw blade (12) is securely
mounted in the blade holder.
•
To remove the saw blade, follow the instruc-
tions above in reverse order.
5.3 Fitting the parallel stop (Fig. 5/Item 11)
•
The parallel stop (11) enables you to saw
parallel cuts.
•
Undo the two locking screws for the parallel
stop (13) on the soleplate (7).
•
Now slide the parallel stop into the guides on
the soleplate (7). You can fit the parallel stop
(11) on either the left or right of the equip-
ment.
•
The guide strip must always face downwards.
Set the required distance using the measu-
rement scale on the parallel stop (11) and
tighten the locking screws for the parallel stop
(13) again.
5.4 Setting the soleplate for miter cuts (Fig. 6)
•
Undo the locking lever for the soleplate (16)
on the soleplate.
•
Pull the sole plate (7) backwards slightly. The
soleplate can now be swiveled a maximum
45° to the left and right.
•
If the soleplate (7) is pushed back to the
front again it will only function in the locking
positions at 0°, 15°, 30° and 45°, which are
marked on the graduated scale for the sole-
plate (9). Move the soleplate into the required
position and tighten the locking lever securing
the soleplate (16).
•
However, the soleplate (7) is also easily set
Anl_TC_JS_85_SPK7.indb 18 Anl_TC_JS_85_SPK7.indb 18
GB
to another angle. To do so, slide the soleplate
(7) backwards, set the desired angle and
retighten the locking lever securing the sole-
plate (16).
•
Important! For miter cuts you must remove
the locking screws for the parallel stop (13)
and the splinter guard (17).
5.5 Adapter for chip extraction system
(Fig. 7/Item 5)
•
Connect your jigsaw to a vacuum cleaner
using the adapter for dust extraction (5). This
will ensure optimum chip extraction from the
workpiece. The benefits are that you will pro-
tect both the equipment and your own health.
Your work area will also be cleaner and safer.
•
Dust created when working may be dange-
rous. Refer to the section entitled "Safety
information".
•
Fit the adapter for chip extraction (5) as
shown in Fig. 7. The adapter for chip extrac-
tion (5) must audibly engage to ensure that it
is secure in the soleplate (7). The adapter for
chip extraction (5) cannot be used for miter
cuts.
•
Fit the vacuum tube of the vacuum cleaner
onto the opening of the adapter for chip ex-
traction (5). Check that the connections are
air-tight.
5.6 Splinter guard (Fig. 15/Item 17)
The splinter guard (17) ensures that the material
you want to cut does not splinter or crack during
sawing. To use the splinter guard (17), proceed
as follows:
1. Bend the two lugs (a) on the soleplate guard
(b) slightly outwards and raise the soleplate
guard.
2. Remove the soleplate guard (b) from the so-
leplate (7) as shown in Fig. 15.
3. Insert the splinter guard (17) into the sole-
plate guard (b). As you do so, make sure that
the arrows on the splinter guard and on the
soleplate guard coincide as shown in Fig. 15.
The soleplate guard (b) can now be placed on the
soleplate (7) again. Proceed in reverse order.
Notice! The splinter guard (17) can be used
only for 0° cuts and must be removed for mi-
ter cuts up to 45°!
- 18 -
17.10.2023 10:33:28 17.10.2023 10:33:28