Christie Vivid LX120 Kurzanleitung Seite 8

OPERATING ON-SCREEN MENU
HOW TO OPERATE ON-SCREEN MENU
You can control and adjust this projector through ON-
SCREEN MENU.
1 DISPLAY MENU
Press the MENU button to display ON-SCREEN MENU.
2 MOVING POINTER
✽
Move pointer ( see below) or adjust the value of the item
by pressing the POINT button(s) on the Side Control or on
the Remote Control Unit.
✽
The pointer is an icon on the ON-SCREEN MENU to
select an item. See figures on section "FLOW OF ON-
SCREEN MENU OPERATION" below.
3 SELECT ITEM
Select an item or set the selected function by pressing the
SELECT button.
FLOW OF ON-SCREEN MENU OPERATION
Display ON-SCREEN MENU
1 Press the MENU button to display the ON-SCREEN
MENU (MENU BAR). A red frame is the POINTER.
Select Menu to be adjusted
2 Move the POINTER (red frame) to MENU ICON that
you want to select by pressing the the POINT LEFT /
RIGHT buttons.
Control or adjust item through ON-SCREEN MENU
3
Press the POINT DOWN button and move the
POINTER (red frame or red arrow) to the ITEM you
want to adjust, and then press the SELECT button to
show the ITEM DATA.
4
Adjust the ITEM DATA by pressing the POINT LEFT /
RIGHT buttons.
For details, refer to the Owner's Manual.
REMOTE CONTROL UNIT
POINT BUTTONS
Used to move the
Pointer UP/ DOWN/
RIGHT/ LEFT.
MENU BUTTON SELECT BUTTON
Used to select the item.
SIDE CONTROL
POINT BUTTONS
Used to move
Pointer UP/ DOWN/
RIGHT/ LEFT.
SELECT BUTTON
Used to select item.
MENU BAR MENU ICON
POINTER
POINTER (red frame)
(red frame)
Press the POINT DOWN
button to move the POINTER.
ITEM
SELECT
BUTTON
ITEM DATA
Press the POINT
LEFT/RIGHT buttons to
adjust the value or set the
function.
TURNING ON / OFF PROJECTOR
TURNING ON PROJECTOR
Press the POWER ON-OFF button on the Side Control or on
the Remote Control Unit to turn on. LAMP indicator dims, and
Cooling Fans start to operate. Preparation Display appears on
the screen and count-down starts. Signal from source appears
after 20 seconds.
Current Input position and Lamp status are also displayed on
the screen for 5 seconds.
TURNING OFF PROJECTOR
1 Press the POWER ON-OFF button on the Side Control or
on the Remote Control Unit, and a message "Power off?"
appears on the screen.
2 Press the POWER ON-OFF button again to turn off the
projector. LAMP indicator lights bright and READY
indicator turns off. After approximate 90 seconds,
READY indicator will light green again and the projector
may be turned on by pressing the POWER ON-OFF
button.
3 Cooling fans will operate for approximate 2 minutes after
the projector is turned off. To power down completely,
turn the MAIN ON/OFF SWITCH to OFF and disconnect
the AC Power Cord.
TO MAINTAIN LIFE OF LAMP, ONCE YOU TURN
THE PROJECTOR ON, WAIT AT LEAST 5 MINUTES
BEFORE TURNING IT OFF.
When Power Management function is ON, the projector detects signal interruption and Projection Lamp is
turned off automatically.
When WARNING TEMP. indicator flashes red, the projector is automatically turned off. Wait at least 5 minutes
before turning on the projector again.
When both WARNING TEMP. and READY indicators to flash, follow procedures below:
1. Turn MAIN ON/OFF SWITCH to OFF.
2. Turn the projector on again.
When WARNING TEMP. indicator continues to flash, follow procedures below:
1. Turn the MAIN ON/OFF SWITCH to OFF and disconnect the AC Power Cord from the AC outlet.
2. Check Air Filters for dust accumulation.
3. Clean Air Filters.
4. Turn the projector on again.
If WARNING TEMP. indicator should still continue to flash, contact the sales dealer where you purchased this
projector or the service center.
LAMP STATUS
INPUT 1
20
Preparation Display disappears
after 20 seconds.
Power off?
Message disappears after 4 seconds.