Agilent Technologies TPS-mobile 969-8400 Bedienungshandbuch Seite 106

ISTRUZIONI ORIGINALI
Window Meanings
N. Read/ Data
Write Type
000 R/W L Start/Stop
(in remote/
Front mode the
window is a
read only)
001 R/W L Low Speed
Activation
008 R/W L Remote
(default) or
Serial
configuration
100 R/W L Soft Start
(write only in
Stop condition)
101 R/W N R1 Set Point
type
102 R/W N R1 Set Point
valve
(expressed in
Hz, W or s)
103 R/W N Set Point delay:
time between
the pump start
and the set
point check
(seconds)
104 R/W L Set Point signal
activation type:
the signal can
be "high level
active" or "low
level active"
105 R/W N Set point
hysteresis
(in % of value)
106 R/W L Water cooling
107 R/W L Active Stop
(write only in
stop)
108 R/W N Baud rate
109 W L Pump life/
cycle time/
cycle number
reset
110 R/W L Interlock type
(default = 1)
Description Admitted
Values
Start = 1
Stop = 0
No = 0
Yes = 1
(default = 0)
Remote = 1
Serial = 0
(default = 1)
YES = 1
NO = 0
0 = Frequency
1 = Power
2 = Time
3 = Normal
4 = Pressure
(default = 3)
(default = 900)
0 to 99999
(default = 0)
0 = high level
active
1 = low level
active
(default = 0)
0 to 100
(default = 2)
0 = NO
1 = YES
0 = NO
1 = YES
600 = 0
1200 = 1
2400 = 2
4800 = 3
9600 = 4
(default = 4)
To reset write '1'
Impulse = 0
Continuous = 1
N. Read/
Write
111 R/W
117 R/W
120 R/W
122 R/W
123 Reserved to Varian service
124
125 R/W
126 R/W
130 Reserved to Varian service
147 R/W
155 R
157 R/W
161 R/W
162 R/W
163 R/W
102/105
TECHNICAL INFORMATION
Data Description Admitted
Type
L Analog output 0 = frequency
type: output 1 = power
voltage signal
(default = 1)
proportional to
frequency or
2 = Pump
power
temperature
3 = Pressure
N Low Speed 250 to "Maximum
frequency rotational
(Hz) frequency"
(win 121)
(default = 700)
N Rotational 900 to "Maximum
frequency rotational
setting (Hz) frequency"
(win 121)
(default = 963)
L Set vent valve On = 1
on/off Off = 0
(on = closed)
(default = 1)
L Set the vent Automatic = 0
valve (see note 1.)
operation
On command = 1
(see note 2.)
N Vent valve 0 to 65535
opening delay
(corresponding to
(expressed in
0 to 13107 sec)
0.2 sec)
N Vent open 0 = infinite
time 1 bit = 0.2 sec
See "vent
connector"
paragraph
N Power limit watt
applied
Read the
maximum
allowable
power
N Gas load type Ø = N
Select the gas 1 = Av
load to the
pump
N Pressure 0 to 10
Reading 0 = 0
Connection 10 = 1 = N
Factor
See "GAUGE
CONNECTOR"
for more details
A R1 Set Point
Pressure
Valve
Valid if min.
101 = 4
Format X.X E.
XX
Where X = 0
to 9 s = + or -
N Pressure unit 0 = mBar
of measure 1 = Pa
2 = Torr
87-901-005-01(A)
Values
2
2