BaByliss 9000 Bedienungsanleitung Seite 3

HOW TO USE YOUR BABYLISS 9000
SAFETY CAUTIONS
• This appliance should only be
used as described within this
instruction book. Please retain
for reference.
IMPORTANT SAFETY
• WARNING: Do not use
this appliance near water
contained in basins,
bathtubs or other vessels.
• This appliance can be used by
children aged from 8 years and
above and persons with reduced
physical, sensory or mental
capabilities or lack of experience
and knowledge if they have been
given supervision or instruction
concerning use of the appliance
in a safe way and understand the
hazards involved. Children shall
not play with the appliance.
Cleaning and user maintenance
shall not be made by children
without supervision.
• When the appliance is used in a
bathroom, unplug it after charge
since the proximity of water
presents a hazard even when
the appliance is switched off.
• For additional protection, the
installation of a residual current
device (RCD) having a rated
residual operating current not
exceeding 30mA is advisable in
the electrical circuit supplying
the bathroom. Ask your installer
for advice.
• This appliance contains
rechargeable batteries that must
be removed before discarding
the appliance. Unplug the
appliance before removing the
batteries. Battery is be disposed
of safely. For further information
on removing the batteries, the
Conair Customer Care Line
(refer to After Sales Service
section for further information).
• WARNING: For the purposes
of recharging the battery, only
use the detachable supply unit
provided with this appliance
(CA86 adaptor).
• If the external flexible cable
or cord of this transformer is
damaged, it shall be replaced by
the manufacturer or their service
agent or a similarly qualified
person in order to avoid a hazard.
• Always place the appliance on a
flat, stable and heat-resistant surface.
• Burn hazard. Keep appliance out
of reach from young children,
particularly during use and
cool down.
• This appliance contains batteries
that cannot be replaced.
• At the end of its life, the unit
should be disposed of at a recycling
centre to safeguard the environment.
If the battery leaks, avoid
touching it and dispose of
it at a recycling centre.
HOW TO USE YOUR BABYLISS 9000
READ THE SAFETY INSTRUCTIONS FIRST.
HOW TO USE
Warning: hot surface! When in use, the appliance
must never come into contact with the scalp, face,
ears and neck.
CHARGING YOUR BABYLISS 9000
HAIR STRAIGHTENER
First select the correct Fix to the adaptor.
adaptor pins for your mains
outlet.
Plug in to the mains. Press on the lock to release
This BaByliss 9000 Hair Straightener is very easy to use
but before you do anything you must take your time
to charge it for 3 hours before the first use. A 3 hour
charge will give you approximately 30 minutes use and
charging your straighter for 5 hours will give you a full
battery charge.
Please note your straightener will not function
while charging.
Whilst your straightener is charging, the LED charging
light will flash slowly and continuously with the colour
indicating the level of battery charge.
Flashing red = below 30% battery charge
Flashing orange = 30% - 49% battery charge
Flashing yellow = 50% - 84% battery charge
Flashing green = 85% - 94% battery charge
Solid green = 95 % - 100% battery charge
Warning: If the charging light suddenly starts to flash
rapidly then the appliance is faulty. If this happens, please
stop charging and remove the adaptor from the mains
and contact our Customer Care Centre for further advice.
INSTRUCTIONS FOR USE
• Remove the silicone plate guard and allow the
straightener plates to open. Please note for safety
reasons you will be not be able to switch your
straightener on when it is in the closed positioned.
• Press and hold the on/off button for 2 seconds
the gentle notification sound indicates that your
straightener is switched on.
• Once the straightener is switched on it will
automatically start heating up to 160°C.
• There are 3 temperature settings 160°C, 180°C
and 200°C which are indicated by the LEDs as
shown below.
• To select the temperature setting press the on/off
button once, twice or three times.
Temperature select
High (200 o C)
Medium (180 o C)
o
Low (160 C)
Default temperature : 160
• The LEDs will flash when your straightener is heating
up and will stop flashing once the target temperature is
reached and it is ready to use.
• If you have delicate, fine, bleached or coloured hair, use
the lower heat setting. For thicker hair, use the higher
heat setting. We suggest when using for the first time
you test the heat settings to ensure you've got the
correct temperature for your hair type. Start on the
lowest setting and increase the temperature as necessary.
• Ensure your hair is dry and combed through.
• Divide hair into sections.
• Take a section of hair and place it between the styling plates.
• Hold hair firmly and slide the straightening plates down
the length of the hair from root to tip.
• Repeat as necessary.
• Allow hair to cool before combing through.
• To switch off your straightener please press and hold
the on/off button for 2 seconds. The gentle notification
sound indicates the straightener has switched off.
• Once your straightener is switched off, place the heat
resistant silicone plate guard over the straightening
plates in a closed position.
• Allow to cool before storing away.
o
C