Elica Vogue Serie Bedienungsanleitung Seite 19

Fig. 9
6. Hook the frame onto the 4 screws (see step 4).
CAUTION! The side of the truss with connection box
corresponds to the side of the control panel with hood
assembled.
7. Tighten the 4 screws.
8. Insert and tightly screw in another 4 screws and 2
washers on the safety fastening holes left free.
Note - only for the suction Version: connect the upper
end of the discharge tube to the discharge device toward
the exterior (e.g. hole in the ceiling).
Note- for Filter Version only: insert the extensions on the
deflector F blocking them with 4 total screws (Picture 9F).
Carry out the electrical connection to the mains power supply,
only turn on the power supply upon completion of assembly.
Fig. 10
9. Couple the two sections of the chimney as cover to the
lattice.
Screw the two sections in the lattice with 4 screws (2 on
the front side and 2 on the back side).
10. Definitely fix the two sections with 4 screws M4x7 (2 on
the front side and 2 on the back side).
11. Apply the upper tabs (pressure fastening).
Fig. 11
12. Fit the control shaft in the correct position by pushing it
upwards.
Connect the electricity.
Fig. 12
13. Hook the 4 lower panels (2 on the front side and 2 on the
back side).
Fix the panels to the structure with 2 side screws and 3
central screws, totally 5 screws each panel.
Fig. 13
14. Apply the 4 aesthetic panels as cover to the lower
panels.
Note- To install the panels in the correct position check
the internal notches:
R= Right panel.
L= Left panel.
Fig. 14
15. Mount the upper covers fixing them with 14 total screws
(7 each cover).
Fig. 15
16. Cut 8 pieces (length 10 mm) of adhesive tape "Dual
Lock".
Apply 2 pieces of tape on the stirrups and 2 on the
covers as shown in picture.
17. Definitely fix the upper covers with 2 stirrups and 8
screws (4 each stirrup).
18. Apply the aesthetic covers.
Fig. 16
19. Apply the lower tabs (pressure fastening).
Turn the mains power on again at the central electrical panel
and check for correct hood operation.
Description of the hood
Fig. 1
1. Control panel
2. Grease filter
3. Grease filter release handle
4. Halogen lamp
5. Vapour catcher
6. Telescopic chimney
7. Air outlet (used for filter version only)
8. Panel
Operation
Use the high suction speed in cases of concentrated kitchen
vapours. It is recommended that the cooker hood suction is
switched on for 5 minutes prior to cooking and to leave in
operation during cooking and for another 15 minutes
approximately after terminating cooking.
The hood is equipped with a "TOUCH" device to control the
lights and speed.
For the correct use please carefully read the intructions below.
Automatic start-up function
The hood is equipped with a temperature sensor which
activates the motor to the first suction speed (power) in the
event that the room temperature in the surrounding area is
higher than 70°C.
The user may switch off or modify the suction speed (power)
(see paragraph "suction speed (power) control").
Suction speed (power) control
The suction speed (power) is cyclical depending on the speed
sequence "stand-by – 1-2-3-4- Stand by -1-2-..." therefore
every time the T1 button is pressed on the control panel, the
suction speed (power) is increased by one level, in order to
switch off (stand-by) if the button is pressed again when the
hood is in suction speed (power) 4.
The hood may be switched off (stand-by) while the hood is set
on any speed by holding down the T1 button on the control
panel for a bit longer (more than 3 seconds).
The hood's suction speed (power) may be determined as the
control panel is equipped with a LED light that changes colors
as follows, depending on the suction speed (power):
19