Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Safety Instructions
FDM 3D Printer Pro 7 Dual
Item No. 2584537
1 Intended use
The product is a 3D printer.
The product is not designed for use in food and medical industries.
The product is intended for indoor use only. Do not use it outdoors. Contact with moisture must
be avoided under all circumstances.
If you use the product for purposes other than those described, the product may be damaged.
Improper use can result in short circuits, fires, electric shocks or other hazards.
The product complies with the statutory national and European requirements. For safety and
approval purposes, you must not rebuild and/or modify the product.
Read the operating instructions carefully and store them in a safe place. Make this product
available to third parties only together with the operating instructions.
All company names and product names are trademarks of their respective owners. All rights
reserved.
2 Latest operating instructions
Download the latest operating instructions at
shown. Follow the instructions on the website.
3 Notes on filaments
PLA filaments will over time absorb moisture and dust when exposed to the open air, which can
affect the printing quality. Seal the filament in an air-tight container when not in use.
4 Description of symbols
The following symbols are on the product/appliance or are used in the text:
For safe and proper use, follow these instructions. Keep them for future reference.
The symbol warns of hazards that can lead to personal injury.
The symbol warns of dangerous voltage that can lead to personal injury by electric
shock.
The symbol warns of hot surfaces that can result in severe burns when touched.
Read the information carefully.
The symbol warns of rotating gears that can crush hands and fingers.
The symbol warns of closing mechanical parts that can crush hands and fingers.
This product must only be used in dry, enclosed indoor areas. It must not become
damp or wet.
5 Safety instructions
Read this document and the accompanying operating instructions carefully
and especially observe the safety information. If you do not follow the safety
instructions and information on proper handling, we assume no liability for
any resulting personal injury or damage to property. Such cases will invali-
date the warranty/guarantee.
5.1 General information
The device is not a toy. Keep it out of the reach of children and pets.
Do not leave packaging material lying around carelessly. This may become dangerous
playing material for children.
If you have questions which remain unanswered by these operating instructions, contact
our technical support service or other technical personnel.
Maintenance, modifications and repairs must only be completed by a technician or an au-
thorised repair centre.
5.2 Handling
Please handle the product carefully. Jolts, impacts or a fall even from a low height can
damage the product.
www.conrad.com/downloads
or scan the QR code
5.3 Mains cable
Do not modify or repair mains supply components including mains plugs, mains
cables, and power supplies. Do not use damaged components. Risk of death by
electric shock!
The mains outlet must be located near to the device and be easily accessible.
Never plug in or unplug the mains plug when your hands are wet.
Never pull the mains plug from the socket by pulling at the cable. Always pull it from the
mains socket using the intended grips.
Unplug the mains plug from the mains socket if you do not use the device for an extended
period of time.
Disconnect the mains plug from the mains socket in thunderstorms for reasons of safety.
Make sure that the mains cable is not squeezed, bent, damaged by sharp edges or put
under mechanical stress.
Avoid excessive thermal stress on the mains cable from extreme heat or cold.
Do not modify the mains cable. Otherwise the mains cable may be damaged. A damaged
mains cable can cause a deadly electric shock.
Do not touch the mains cable if it is damaged.
– First, power down the respective mains socket (e.g. via the respective circuit breaker)
and then carefully pull the mains plug from the mains socket.
– Never use the product if the mains cable is damaged.
A damaged mains cable may only be replaced by the manufacturer, a workshop commis-
sioned by the manufacturer or a similarly qualified person, so as to prevent any danger.
Ensure that cables are not pinched, kinked or damaged by sharp edges.
Always lay cables so that nobody can trip over or become entangled in them. This poses
a risk of injury.
5.4 Operating environment
Only operate the device in moderate climates, never in tropical climates.
Do not place the product under any mechanical stress.
Protect the appliance from extreme temperatures, strong jolts, flammable gases, steam
and solvents.
Protect the product from high humidity and moisture.
Protect the product from direct sunlight.
Do not switch the product on after it has been taken from a cold to a warm environment.
The condensation that forms might destroy the product. Allow the product to reach room
temperature before you use it.
5.5 Operating location
Choose the site of operation so that children cannot reach the product.
In operation, there will be noise and, depending on the material used, smells. Observe this
when selecting the site of setup and the material. Ensure ventilation or install an extraction
system. Do not inhale arising vapours. When using any other than the recommended mate-
rial, poisonous vapours or gases may develop.
Set up the 3D printer only on a stable, horizontal, sized surface.
Never operate the device unattended.
5.6 Operation
Nozzle, extruder, and print bed become very hot during use and can cause serious
burns when touched. Let hot components cool down to room temperature before
touching.
Molten filament is very hot and can cause serious burns when touched. Do not touch fila-
ment that comes out of the extruder.
Never reach into the 3D printer in operation. The mechanically moved parts within the
printer pose a high risk of injury!
Disconnect the device from the mains before maintenance work or (unplug the mains plug)
and let it cool down.
Never place containers containing liquids, e.g. glasses, vases, etc. on the device or in its vi-
cinity and do not pour any liquids out over the device. Liquids may get into the housing and
impair electrical safety. This also poses great danger of or potentially fatal electric shock!
If this is the case, power down the respective mains socket on all poles (e.g. switch off
circuit breaker and FI switch) and then pull the mains cable from the socket. Disconnect all
lines from the device. Do not operate any part of the product anymore afterwards but take
it to a specialist workshop.
Never place any sources of open such as lit candles, on or right next to the device.
Consult an expert when in doubt about the operation, safety or connection of the appliance.
If it is no longer possible to operate the product safely, take it out of operation and protect
it from any accidental use. DO NOT attempt to repair the product yourself. Safe operation
can no longer be guaranteed if the product:
– is visibly damaged,
– is no longer working properly,
– has been stored for extended periods in poor ambient conditions or
– has been subjected to any serious transport-related stresses.
Werbung
