Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Installing or removing battery cartridge
(Fig. 1)
• Always switch off the tool before installation or removal
of the battery cartridge.
• To remove the battery cartridge, withdraw it from the
tool while sliding the button on the front of the cartridge.
• To insert the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Always insert it all the way until it locks in
place with a little click. If you can see the red part on
the upper side of the button, it is not locked completely.
Insert it fully until the red part cannot be seen. If not, it
may accidentally fall out of the tool, causing injury to
you or someone around you.
• Do not use force when inserting the battery cartridge. If
the cartridge does not slide in easily, it is not being
inserted correctly.
Indicating the remaining battery capacity
Only for battery cartridges with the indicator (Fig. 2)
Press the check button on the battery cartridge to indicate
the remaining battery capacity. The indicator lamps light
up for a few seconds.
Indicator lamps
Lighted
Off
NOTE:
• Depending on the conditions of use and the ambient
temperature, the indication may differ slightly from the
actual capacity.
• The first (far left) indicator lamp will blink when the
battery protection system works.
Switch action (Fig. 3)
CAUTION:
• Before inserting the battery cartridge into the tool,
always check to see that the switch trigger actuates
properly and returns to the "OFF" position when
released.
• Change the direction of rotation only when the tool
comes to a complete stop. Changing it before the tool
stops may damage the tool.
The switch is reversible, providing either clockwise or
counterclockwise rotation. To start the tool, simply pull the
lower part (A) of the switch trigger for clockwise or the
6
Remaining
capacity
Blinking
75% to 100%
50% to 75%
25% to 50%
0% to 25%
Charge the
battery.
The battery may
have
malfunctioned.
upper part (B) for counterclockwise. Release the switch
trigger to stop.
Lighting up the front lamp (Fig. 4)
CAUTION:
• Do not look in the light or see the source of light
directly.
Push the upper position of the lamp switch for turning on
the light and the lower position for off.
NOTE:
• Use a dry cloth to wipe the dirt off the lens of lamp. Be
careful not to scratch the lens of lamp, or it may lower
the illumination.
• The light is provided with anti excessive discharge
circuit. When the lamp does not light up even after the
light switch is turned on, there is likely to be battery
power drop. Try to charge the battery cartridge.
• Keep the lamp switch in "off" position while not in need
of the light.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and the
battery cartridge is removed before carrying out any
work on the tool.
Selecting correct socket
Always use the correct size socket for bolts and nuts. An
incorrect size socket will result in inaccurate and
inconsistent fastening torque and/or damage to the bolt or
nut.
Installing or removing impact socket
Country specific
CAUTION:
• Make sure that the impact socket and the mounting
portion are not damaged before installing the
impact socket.
• After inserting the impact socket, make sure that it
is firmly secured. If it comes out, do not use it.
Tool with the ring spring
For impact socket without O-ring and pin (Fig. 5)
Push the impact socket onto the square drive until it locks
into place.
To remove the impact socket, simply pull it off.
For impact socket with O-ring and pin (Fig. 6)
Move the O-ring out of the groove in the impact socket
and remove the pin from the impact socket. Fit the impact
socket onto the square drive so that the hole in the impact
socket is aligned with the hole in the square drive.
Insert the pin through the hole in the impact socket and
square drive. Then return the O-ring to the original
position in the impact socket groove to retain the pin.
To remove the impact socket, follow the installation
procedures in reverse.
Tool with the detent pin (Fig. 7)
Align the hole in the side of the impact socket with the
detent pin on the square drive and push the impact socket
Werbung
