Makita DCU180 Betriebsanleitung Seite 21

Loading objects
CAUTION:
Before loading objects on the
machine, make sure that the power is off and the
brake lever is locked.
CAUTION:
If the rear wheels are installed,
make sure that the rear wheel brake is locked
before loading objects on the machine.
CAUTION:
Before loading objects on the
machine, make sure that the carrier or bucket is
locked.
CAUTION:
Be sure to load objects within the
carrier or bucket. If objects are sticking out of the
carrier or bucket, they may fall or collapse if they
touch obstacles.
► Fig.44
CAUTION:
Be sure to load objects so that
they are below eye level. If the load is too high, it is
dangerous because the view is obscured. Also, there
is a risk of overturning and injury because the load is
likely to be unbalanced.
► Fig.45
When loading objects on the carrier, secure the objects
with ropes and tie them down to the rope hooks.
► Fig.46
Dumping objects
CAUTION:
Lift the carrier or bucket on flat
and stable ground. Operation on unstable ground
my cause an accident or injury.
You can dump the objects by lifting and tilting the carrier
or bucket.
1.
Stop the machine, and then lock the brakes.
NOTICE:
It is recommended to block the front
wheel to stabilize the machine.
2.
Release the lock lever.
3. Stand at the side of the machine, hold the handle
with one hand, and then lift and tilt the carrier or bucket
by pushing up the carrier frame with the other hand.
► Fig.47
CAUTION:
Hold the handle and carrier frame
firmly, and work in a stable posture.
CAUTION:
Keep the load to a minimum. If the
load is large, do not try to lift the carrier. Reduce
the load, and then lift the carrier.
CAUTION:
After dumping the objects, be sure
to lock the carrier or bucket.
MAINTENANCE
CAUTION:
Always be sure to park the
machine on flat ground and lock the brake lever
before storage or attempting to perform inspec-
tions or maintenance.
CAUTION:
If the rear wheels are installed,
make sure that the rear wheel brake is locked
before storage, inspections, or maintenance.
CAUTION:
Always be sure that the lock
key and battery cartridge are removed from
the machine before storage, inspections, or
maintenance.
CAUTION:
Always remove the lock key when
the machine is not in use. Store the lock key in a
safe place out of reach of children.
Periodic checks
• Check that the bolts and nuts are tightened firmly.
► Fig.48
• Check that the carrier is locked when the lock
lever is fully pulled down.
► Fig.49: 1. Carrier lock 2. Lock lever
• Check that the brake lever works properly.
► Fig.50: 1. Brake lever
WARNING:
dle when you fully pull the lever, the brake is not
working properly. Adjust the brake, or ask your
local Makita Service Center for repairs.
• Check to see if the front wheel is not damaged or
flat. Check that the air in the tire for the front wheel
is sufficient.
Cleaning the machine
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
NOTICE:
Pour the water below the carrier or
bucket when cleaning the machine with running
water. Do not use the high pressure washer for
cleaning.
Remove mud, dirt, and the like from the machine. Clean
the machine with running water. After the cleaning, wipe
the machine with a dry cloth.
Storage
Remove the lock key. Store the machine in a safe place
out of the reach of children.
When storing the machine, the handles can be turned
toward the front. Remove the short hexagonal bolts
and shoulder bolts using the wrench included in the
package. Turn the handles toward the outside, and then
rotate the handles to the front. Tighten the shoulder
bolts and short hexagonal bolts to fix the handles.
► Fig.51: 1. Shoulder bolt 2. Short hexagonal bolt
21 ENGLISH
If the brake lever reaches the han-