Makita DCU180 Betriebsanleitung Seite 18

Assembling and installing carrier
Optional accessory
1. Take out the carrier from the box, attach the side
rails to the base frame, and then tighten the thumb nuts
to fix the rails.
► Fig.19: 1. Thumb nut
2. Place the carrier on the base unit, and then insert
the hexagonal bolts and washers into the frames from
the top. Tighten the washers and spring washers and
butterfly nuts from the bottom to fix the carrier.
► Fig.20: 1. Long hexagonal bolt 2. Short hexagonal
bolt 3. Washer 4. Spring washer 5. Butterfly
nut
NOTICE:
Use the long bolts for the front, and the
short bolts for the rear.
Installing bucket
Optional accessory
Place the bucket on the base unit, insert the hexagonal
bolts into the frames, and then tighten the washers and
spring washers and butterfly nuts from the bottom to fix
the bucket.
► Fig.21: 1. Hexagonal bolt 2. Washer 3. Spring
washer 4. Butterfly nut
FUNCTIONAL
DESCRIPTION
Installing or removing battery
cartridge
CAUTION:
Always switch off the machine
before installing or removing of the battery
cartridge.
CAUTION:
Make sure that you lock the battery
cover before use. Otherwise, mud, dirt, or water may
cause damage to the product or the battery cartridge.
CAUTION:
Always install the battery cartridge
fully until the red indicator cannot be seen. If not,
it may accidentally fall out of the machine, causing
injury to you or someone around you.
CAUTION:
Do not install the battery cartridge
forcibly. If the cartridge does not slide in easily, it is
not being inserted correctly.
CAUTION:
Do not use the high-temperature
battery cartridge. When the high-temperature bat-
tery cartridge is used, the machine stops automati-
cally before a short beep sound is emitted, and may
cause an injury.
Installing the battery cartridge
1. Rotate the lock lever, and then open the cover of
the battery box.
► Fig.22: 1. Lock lever 2. Cover
2. Align the tongue on the battery cartridge with the
slot on the battery box, and then slide the cartridge until
it locks in place with a little click. If you can see the red
indicator on the upper side of the button, battery car-
tridge is not locked completely.
► Fig.23: 1. Battery cartridge
3. Insert the lock key in the place shown in the figure
as far as it will go.
► Fig.24: 1. Lock key
NOTE: If the lock key is not inserted completely, the
machine does not work.
4. Close the cover of the battery box, and then rotate
the lock lever.
► Fig.25: 1. Lock lever 2. Cover
Removing the battery cartridge
1. Rotate the lock lever, and then open the cover of
the battery box.
2. Pull out the battery cartridge from the battery box
while sliding the button on the front of the cartridge.
► Fig.26: 1. Button
3. Pull out the lock key.
4. Close the cover of the battery box, and then rotate
the lock lever.
Machine / battery protection system
The machine is equipped with a machine/battery
protection system. This system automatically cuts off
power to the motor to extend machine and battery life.
The machine will automatically stop during operation
if the machine or battery cartridge is under one of the
following conditions. A short beep sound is emitted
before the machine stops automatically. The battery
indicators and LED indicators blink while the beep
sound is emitted.
Overload protection
When the machine is operated in a manner that causes
it to draw an abnormally high current, the machine auto-
matically stops without any indication. In this situation,
turn the machine off and remove the cause of overload,
and then turn the machine on to restart.
Overheat protection
When the machine is overheated, the machine stops
automatically. Let the machine cool down before turning
the machine on again. The overheat protection is likely
to work under high temperature environment.
Overdischarge protection
When the battery capacity becomes low, the machine
stops automatically. If the machine does not operate
even when the switches are operated, remove the
battery cartridge and charge it.
18 ENGLISH