Black+Decker BEH200 Bedienungsanleitung Seite 6

ENGLISH
To select reverse rotation, push the forward/reverse
u
button to the right.
Warning! Never change the direction of rotation while the
motor is running.
Setting the drilling depth (fig. E)
Slacken the side handle (6) by turning the knob (6a)
u
counter clockwise.
Set the depth guage (7) (Not Supplied) to the desired
u
position. The maximum drilling depth is equal to the
distance between the tip of the drill bit and the front end of
the depth guage.
Tighten the side handle by turning the knob (6c)
u
clockwise.
Selecting the drilling mode (fig. F)
For Impact drilling in masonry and concrete, set the
u
drilling mode selector (4) to the
For drilling in steel, wood and plastics or for screw driving
u
set the operating mode selector (4) to the
Switching on and off
To switch the tool on, press the variable speed
u
switch (1). The tool speed depends on how far you
press the switch. As a general rule, use low speeds
for large diameter drill bits and high speeds for smaller
diameter drill bits.
For continuous operation, press the lock-on button (2)
u
and release the variable speed switch. The lock on button
is available only at full speed in forward mode. In the
reverse mode, the lock on button is not available.
To switch the tool off, release the variable speed switch.
u
To switch the tool off when in continuous operation,
press the variable speed switch again and release it.
Always hold the tool as shown in figure E.
Accessories
The performance of your tool depends on the accessory used.
BLACK+DECKER accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
Maintenance
Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
Switch off and unplug the appliance/tool.
u
Or switch off and remove the battery from the appliance/
u
tool if the appliance/tool has a separate battery pack.
6
(Original instructions)
q
position.
r
position.
Or run the battery down completely if it is integral and then
u
switch off.
Unplug the charger before cleaning it. Your charger does
u
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your appliance/tool/
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust
u
from the interior (when fitted).
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
u
Connect the brown lead to the live terminal in the new
u
plug.
Connect the blue lead to the neutral terminal.
u
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 5 A.
Protecting the environment
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions.
Further information is available at www.2helpU.com
Technical data
Input voltage V
AC
Power input W
No load speed min
-1
Max. drilling capacity
Concrete mm
Steel mm
Wood mm
Weight kg
Level of sound pressure according to EN 62841:
Sound pressure (L ) 88 dB(A), uncertainty (K) 5 dB(A)
pA
Sound power (L ) 99 dB(A), uncertainty (K) 5 dB(A)
WA
Vibration total values (triax vector sum) according to EN 62841:
Impact drilling into concrete (a
Drilling into metal (a , ) 2.7 m/s
h
D
BEH200
0 ~ 2900
1.69 with side handle
2 2
) 17.7 m/s , uncertainty (K) 1,5 m/s
h,ID
2 2
, uncertainty (K) 1,5 m/s
230
500
13
13
20