Timer Operation - Kaisai KPPH-09HRG29 Bedienungsanleitung

SET TEMPERATURE( C) SET TEMPERATURE( C)
AUTO AUTO
COOL COOL
DRY DRY
TIMER ON TIMER ON
HEAT HEAT
MODE MODE
SWING SWING
EN
FAN FAN
HIGH HIGH
MED MED
LOW LOW
TEMP TEMP
ON/OFF ON/OFF
FAN SPEED FAN SPEED
TIMER ON TIMER ON
ECONOMY ECONOMY
1 1
TIMER OFF TIMER OFF
RESET LOCK RESET LOCK
2 2
LED LED
DISPLAY DISPLAY

Timer operation

Timer operation
press the TIMER ON button can set the auto-on press the TIMER ON button can set the auto-on
time of the unit. And press the TIMER OFF button time of the unit. And press the TIMER OFF button
can set the auto-off time of the unit. can set the auto-off time of the unit.
To set the Auto-on time. To set the Auto-on time.
1. Press the TIMER ON button. The remote 1. Press the TIMER ON button. The remote
controller shows TIMER ON, the last Auto-on controller shows TIMER ON, the last Auto-on
setting time and the signal "h" will be shown on setting time and the signal "h" will be shown on
the LCD display area. Now it is ready to reset the the LCD display area. Now it is ready to reset the
Auto-on time to START the operation. Auto-on time to START the operation.
2. Push the TIMER ON button again to set desired 2. Push the TIMER ON button again to set desired
Auto-on time. Each time you press the button, Auto-on time. Each time you press the button,
the time increases in 30 minutes increments, up the time increases in 30 minutes increments, up
to 10 hours, then at 1 hour increments up to 24 to 10 hours, then at 1 hour increments up to 24
hours. hours.
3. After setting the TIMER ON ,there will be a one- 3. After setting the TIMER ON ,there will be a one-
half second delay before the remote controller half second delay before the remote controller
transmits the signal to the air conditioner. Then, transmits the signal to the air conditioner. Then,
after approximately another 2 seconds, the after approximately another 2 seconds, the
signal "h" will disappear and the set temperature signal "h" will disappear and the set temperature
will re-appear on the LCD display window. will re-appear on the LCD display window.
To set the Auto-off time. To set the Auto-off time.
1. Press the TIMER OFF button. The remote 1. Press the TIMER OFF button. The remote
controller shows TIMER OFF, the last Auto-off controller shows TIMER OFF, the last Auto-off
setting time and the signal "h" will be shown on setting time and the signal "h" will be shown on
the LCD display area. Now it is ready to the LCD display area. Now it is ready to
reset the Auto-off time to START the operation. reset the Auto-off time to START the operation.
2. Push the TIMER OFF button again to set desired 2. Push the TIMER OFF button again to set desired
Auto-off time. Each time you press the button, Auto-off time. Each time you press the button,
the time increases in 30 minutes increments, up the time increases in 30 minutes increments, up
to 10 hours, then at 1 hour increments up to 24 to 10 hours, then at 1 hour increments up to 24
hours. hours.
3. After setting the TIMER OFF ,there will be a one- 3. After setting the TIMER OFF ,there will be a one-
half second delay before the remote controller half second delay before the remote controller
transmits the signal to the air conditioner. Then, transmits the signal to the air conditioner. Then,
after approximately another 2 seconds, the after approximately another 2 seconds, the
signal "h" will disappear and the set temperature signal "h" will disappear and the set temperature
will re-appear on the LCD display window. will re-appear on the LCD display window.
74