Intended Use - Makita HR003G Betriebsanleitung

Intended use

The tool is intended for hammer drilling and drilling in
brick, concrete and stone as well as for chiselling work.
It is also suitable for drilling without impact in wood,
metal, ceramic and plastic.
Noise
The typical A-weighted noise level determined accord-
ing to EN62841-2-6:
Model HR001G
Sound pressure level (L
Sound power level (L ) : 103 dB (A)
WA
Uncertainty (K) : 3 dB (A)
Model HR002G
Sound pressure level (L
Sound power level (L ) : 104 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Model HR003G
Sound pressure level (L
Sound power level (L ) : 103 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Model HR004G
Sound pressure level (L
Sound power level (L ) : 104 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Model HR001G with DX12
Sound pressure level (L
Sound power level (L ) : 107 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Model HR002G with DX14
Sound pressure level (L
Sound power level (L ) : 105 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Model HR003G with DX12
Sound pressure level (L
Sound power level (L ) : 107 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Model HR004G with DX14
Sound pressure level (L
Sound power level (L ) : 105 dB (A)
WA
Uncertainty (K) : 3 dB(A)
NOTE: The declared noise emission value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared noise emission value(s) may
also be used in a preliminary assessment of exposure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the
tool is used especially what kind of workpiece is
processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
) : 92 dB (A)
pA
) : 93 dB(A)
pA
) : 92 dB(A)
pA
) : 93 dB(A)
pA
) : 96 dB(A)
pA
) : 94 dB(A)
pA
) : 96 dB(A)
pA
) : 94 dB(A)
pA
Vibration
The following table shows the vibration total value
(tri-axial vector sum) determined according to applica-
ble standard.
Model HR001G
Work mode Vibration
emission
Hammer 15.0 m/s
drilling into
7.9 m/s
concrete
(a )
h, HD
Hammer 13.5 m/s
drilling into
6.5 m/s
concrete with
DX12 (a )
h, HD
Chiselling 11.1 m/s
(a )
h, CHeq
6.7 m/s
Model HR002G
Work mode Vibration
emission
Hammer 15.6 m/s
drilling into
6.5 m/s
concrete
(a )
h, HD
Hammer 14.3 m/s
drilling into
6.4 m/s
concrete with
DX14 (a )
h, HD
Chiselling 11.4 m/s
(a )
h, CHeq
5.6 m/s
Model HR003G
Work mode Vibration
emission
Hammer 15.0 m/s
drilling into
7.9 m/s
concrete
(a )
h, HD
Hammer 13.5 m/s
drilling into
6.5 m/s
concrete with
DX12 (a )
h, HD
Chiselling 11.2 m/s
(a )
h, CHeq
7.1 m/s
12 ENGLISH
Uncertainty (K) Applicable
standard /
Test condition
2 2
2.5 m/s EN62841-2-6
2 2
1.5 m/s Recommended
practical
operation*
2 2
1.5 m/s EN62841-2-6
2 2
1.5 m/s Recommended
practical
operation*
2 2
1.5 m/s EN62841-2-6
2 2
1.5 m/s Recommended
practical
operation*
Uncertainty (K) Applicable
standard /
Test condition
2 2
2.4 m/s EN62841-2-6
2 2
1.5 m/s Recommended
practical
operation*
2 2
2.0 m/s EN62841-2-6
2 2
1.5 m/s Recommended
practical
operation*
2 2
1.5 m/s EN62841-2-6
2 2
1.5 m/s Recommended
practical
operation*
Uncertainty (K) Applicable
standard /
Test condition
2 2
2.5 m/s EN62841-2-6
2 2
1.5 m/s Recommended
practical
operation*
2 2
1.5 m/s EN62841-2-6
2 2
1.5 m/s Recommended
practical
operation*
2 2
1.5 m/s EN62841-2-6
2 2
1.5 m/s Recommended
practical
operation*