Hauff-Technik HSI90 Montageanleitung Seite 5

Schrägpaket
HSI90/HSI150
EN Safety Instructions and Information
Target Group
The installation may only be carried out by technical experts.
Qualified and trained individuals carrying out installation must have
• knowledge of general safety and accident prevention regulations as amended,
• knowledge of how to use safety equipment,
• knowledge of how to use hand tools and electric tools,
• knowledge of the relevant standards and guidelines for laying pipes/cables and
for backfilling utility trenches as amended,
• knowledge of the regulations and installation guidelines of the supply company
as amended,
• knowledge of the waterproof concrete directive and building waterproofing
standards as amended.
General information and intended use
In line with their intended use, our products have been developed solely for instal-
lation in buildings made of state-of-the-art materials. Insofar as no express written
confirmation has been provided by us, we do not accept any liability for any other
purposes or purposes going beyond the above.
For warranty conditions, please see our current General Terms and Delivery Condi-
tions. We explicitly draw your attention to the fact that no warranty whatsoever
applies for any subsequent damage occurring as a result of failure to follow the
installation instructions or if our products are used incorrectly or combined with
third-party products.
Slanted wall inserts are tested by FHRK according to current test guidelines
and bear the seal "FHRK Quality".
The slanted wall insert is for slanted cable entrie from any direction. It allows an
optimum bending radius when feeding in and sealing cables or when connecting
cable ducts.
Safety
This section provides an overview of all the main safety aspects for optimum pro-
tection of personnel and a safe installation process.
A failure to observe the instructions and safety information set out here may re-
sult in significant hazards.
During installation of the slanted wall insert it is imperative to observe the relevant
professional association rules, the VDE provisions, the relevant national safety and
accident prevention regulations and your company's guidelines (work and proce-
dure instructions).
The fitter must wear the relevant protective clothing.
Only intact components may be installed.
The following instructions are to be observed prior to installa-
tion of the slanted wall insert HSI90/HSI150:
WARNING!
Risk of injury in the event of improper installation!
Improper installation can result in significant bodily harm and property dam-
age.
• Observe the nationally applicable laying and filling regulations for pipes and ca-
bles.
NOTICE!
No sealing due to incorrect installation!
Improper installation can result in damage.
• The relevant country specific standards and regulations are to be observed
when carrying out concreting work. This applies especially to concrete con-
struction elements according to EN206-1 which are impermeable to water.
• The incorrect laying of cables or ducts and improper filling of the cable trench
causes settlement, which can lead to damage and leaks.
• Only open cable entries just before fitting with cables to avoid accidental dam-
age during foundation works.
• The slanted wall insert should not be supposed to mechanical load through ca-
bles or pipes.
• Any slanted wall inserts that are not required may be used as pressure-tight
back-up entries if there is an undamaged Hauff quality seal on the closing
cover.
• Do not knock the blind cover in with a hammer or sharp object!
• Open slanted wall inserts, which are used as back-up entries or closing cover
which have been opened accidentally, should be fitted with new HSI 150
DT/DTS respectively HSI90 D blind covers.
• Do not reuse uninstalled or damaged closing covers.
• When tapping in the safety cover (second sealing cover), the bayonet mounting
and the seal seat for the O-ring of the seal packing must not be damaged.
• Before mounting a system cover in the wall insert, clean the interior of any dirt
and check the sealing surfaces for any damage.
• Do not use cleaning agents containing solvents to clean the slanted wall insert.
We recommend using the cable cleaner KRMTX.
Art. Nr.: 5090020175 Rev.: 03/2023-07-14
• For details of other accessories and further information, see www.hauff-tech-
nik.de and the technical data sheets as well as the safety data sheet.
Personnel requirements
Qualifications
WARNING!
Risk of injury in case of inadequate qualification!
Improper handling can result in significant bodily harm and property dam-
age.
• Installation may only be carried out by qualified and trained individuals who
have read and understood these instructions.
Skilled experts
Based on their specialist training, skills, experience and familiarity with the rele-
vant provisions, standards and regulations, skilled experts are able to carry out the
work assigned, independently identifying and avoiding potential hazards.
Transport, packaging, scope of delivery and storage
Safety instructions in connection with transport
NOTICE!
Damage in the event of improper transport!
Significant damage can occur in the event of improper transport.
• When unloading packaging items on delivery and in the course of in-house
transport, proceed with care and observe the symbols on the packaging.
Transport inspection
Inspect the delivery immediately on receipt for completeness and transport dam-
age. In the event of transport damage being visible from the outside, proceed as
follows:
• Do not accept the delivery or only do so subject to reservations.
• Make a note of the extent of damage in the transport documentation or deliv-
ery note provided by the transporter.
• Submit a claim for every defect as soon as it has been identified.
• Claims for damages can only be asserted within the applicable claim
period.
Scope of delivery
The scope of delivery of the slanted wall insert includes:
• Montagerahmen inkl. Schutzfolie mit einer Dreistegdichtung
• Polystyrene wedge(s)
• Attachment frame
• Pressure-tight closing covers
• Quality seals
Accessories
• Closing cover HSI150 DT/DTS resp. HSI90 D (for pressure-tight re-closure)
Storage
NOTICE!
Damage due to improper storage!
Significant damage can occur in the event of improper storage.
• The n.v. is to be protected from damage, damp and soiling prior to installation.
Only intact components may be installed.
• The slanted wall insert must be stored in such a way that it is not exposed to
low temperatures (< 5 °C), high temperatures (> 30 °C) or direct sunlight.
Disposal
If no return or disposal agreement has been concluded, recycle dismantled com-
ponents after they have been properly dismantled:
• Metal remains are to be scrapped according to existing environmental regula-
tions.
• Dispose of elastomers according to existing environmental regulations.
• Dispose of plastics according to existing environmental regulations.
• Dispose of packaging material according to existing environmental regulations.
5