Werbung
GB
1. Assembly of the front wheels
Place the body with the underside facing up. To mount the front wheels, slide a washer onto the
front axle. Put a wheel on the axle and slide another washer onto it. Fix the whole thing with a
nut and finally put on a wheel cover.
2. Assembly of the rear wheels
Plug the motor onto the rear axle. Slide a drive wheel and
a washer onto the rear axle. Secure it with a nut. Now put the wheel cover on the wheel.
Repeat on the other side.
3. Mounting the Steering Wheel
Connect the cable from the steering wheel to the cable on the dashboard. Install the steering
wheel (3) in the intended position until they click into place.
4. Battery connection
Connect all connectors as shown. Only connect plug connections that fit into each other and
take care not to reverse polarity. Make sure that the red cable and the black cable are
connected to the respective connectors of the same colour. Check the power supply by
pressing the ON/OFF switch on the model. If the power supply is working, you will hear a motor
noise.
5. Assembling the seat
Slide the two pins at the rear of the
seat into position in the body and secure the seat with two screws.
6. Windshield assembly
Align the windshield with the corresponding openings on the car body, insert and push them
into place.
7. Assembling the mirrors
Push the rear view mirrors into the intended position until they click into place.
1
1
3
1
4
2
5
Functions transmitter
1
Forward
2
Backward
3
Speed
4
Speed display
5
Left
6
Brake
7
Right
8
Battery compartment
Fitting the batteries
Observe the polarity..
2
3
4
5
6
6
2
3
4
5
6
7
Battery warning:
Non-rechargeable batteries are not to be recharged!
Do not open! Do not dispose of in fire!
Do not mix old and new batteries!
Do not mix alkaline batteries, standard (carbon-zinc) or
rechargeable batteries!
Rechargeable batteries are to be removed from the toy before
being charged!
Rechargeable batteries are only to be charged under adult
supervision!
The supply terminals are not to be short-circuited!
8. Charging Your Vehicle
•
The power swich must be turned in OFF position when charging.
•
Plug the charger port into the input socket and plug the charger plug into a wall outlet.
The battery will begin charging.
•
The charge time is 6 hours.
•
When the vehicle begins to run slowly, recharge thebattery.
•
Do not charge the battery more than once within 24 hours.
•
Charger and battery heat up during the charging process.
Warning!
•
The charger is not a toy. Only use the charger supplied.
•
The battery may only be charged by or under the supervision of an adult.
•
The terminals must not be short-circuited.
•
The charger must be checked regularly for damage to the cable, plug, housing and other
parts. If any damage is found, the charger must not be used until the damage has been
repaired.
•
Let the model cool off sufficiently after each use before putting it back into operation.
When using an additional batteries let it cool off for minimum 15 minutes until the
model is operated again. Overheating can damage the electronics or may result in fire.
•
Always disconnect the model from the charger immediately after charging. Always
disconnect the charger from the power supply immediately after disconnecting the
model. Inserting the rechargeable model or charger after charging will result in damage
tothe model, charger or the power supply (fire hazard).
•
Use the charger only in dry rooms.
Functions
1
Soundboard
2
ON/OFF switch
With the ON/OFF switch you start the vehicle.
3
Light button
4
Shift Lever:
Forward:
Press the "Forward-backward switch" on the "Forward" position.
Press the "Foot pedal", the model drives forward
Stop:
The model will brake automatically, when your child's foot remove from the
"Foot pedal". Press the "Forward-backward switch" in the middle.
Reverse:
Press the "Forward-backward switch" on the "Backward" position.
Press the "Foot pedal", the model drives backward.
Important! The vehicle must be stationary before changing direction or speed.
Otherwise the gear unit and/or the motor could be damaged.
5
Foot pedal
6
Horn button
7
Music button
7
Soundboard
1
USB
2
Bluetooth/Music
By pressing the button shortly Bluetooth will turn on.
By pressing the button shortly again music will start to play.
3
Song button
4
Music/V-
Press = previous, long press = Volume down
5
Music/V+
Press = Next, long press = Volume up
6
Voltage display
8
Binding transmitter and model
Press and hold the forward (1) and reverse (2) buttons simul-
taneously until the speed indicator light (4) flickers. Now switch
on the car and you will see that the speed indicator light stops
flickering, which means that the binding process was successful.
Now the model can be controlled with the transmitter.
9
Werbung
