Werbung
GB
1.
Attach the left Rear Wheel
Turn the body over
•
Slide the driving wheel (2) onto the rear axle. And keep the driving wheel match with the
•
gear box.
Slide the Washer (4) onto the rear axle.
•
Tighten a Locknut (5) to the end of the rear axle with a spanner.
•
Fit the Wheel cover (6) to the wheel. Repeat for the other side.
•
2.
Attach the Front Wheels
Slide a washer (4) onto the front axle.
•
Slide the normal wheel (3) onto the front axle and slide a washer (4) onto the front axle.
•
Tight a Locknut (5) to the end of the front axle with a spanner.
•
"Snap" the wheel cover (6) to the wheel. Repeat this step for the other side.
•
3.
Steering wheel assembly
Connect the cable from the steering wheel to the cable of the dashboard (3.1). Install the
steering wheel (11) in the Intended position and secure it with the Safety pin (12) and nut (13)
4.
Attach the view mirrors and the windshield
4. Install wing mirror (7) to the designated position, and fasten it.
4.1 Insert the tabs on the windshield (8) in the slots on the vehicle body, push until you hear it
click into place.
5.
Attach Seat
Position the seat (9) over the vehicle body, by inserting the pins on the seat into the body.
Tighten two M4 x 12 machine screws (10) with a screwdriver.
6.
Assembly for adjusting the seat
Position the seat so the seat rails slide into the rails on the model (7.1)
•
Press the button (7.2) below the seat and slide the seat backwards
•
CAUTION: Make sure that the seat locks into place while adjusting. The seat can be
locked in three different positions.
1
2
5
Battery warning:
Non-rechargeable batteries are not to be recharged!
Do not open! Do not dispose of in fire! Do not mix old and new batteries!
Do not mix alkaline batteries, standard (carbon-zinc) or rechargeable batteries!
Rechargeable batteries are to be removed from the toy before being charged!
Rechargeable batteries are only to be charged under adult supervision!
The supply terminals are not to be short-circuited!
Caution
Always switch off the model immediately after each use. Immediately after each use the battery should be disconnected from the model. The battery can be deeply discharged by leaving it switched on
accidentally or leaving it plugged in. Deep discharge causes the battery to lose power or can be damaged to such an extent that charging or discharging is no longer possible or the battery can self-ignite
during charging or discharging (fire hazard). Never attempt to charge or discharge deeply discharged batteries. The battery voltage should never fall below 11,9 volts to avoid deep discharge. The fully char-
ged battery has a voltage of approx. 13 Volt. After use, the intact battery should be fully charged immediately after a cooling phase of at least 10 minutes but at the latest after 12 hours to avoid subsequent
deep discharge by self-discharge. If the battery is not used or stored for a longer period of time, the battery should be checked for voltage (min. 12,3 volts) or damage at least every 3 months and charged
or disposed of if necessary.
8
6
3
7
4
7.
Battery connection
•
Open the boot lid and connect the battery with the cable of the body.
•
Only plug matching connectors into eachother and be sure not to reverse the polarity.
8.
Charging Your Vehicle
•
The power swich must be turned in OFF position when charging.
• Insert the charger into the socket - the LED lights up green. Connect the charger to
the charging socket.
•
The LED on your charger lights up red as long as the battery is being charged. If the LED
lights green again, the battery is fully charged.
•
The charge time is 9 hours.
•
Do not charge the battery more than once within 24 hours.
•
Charger and battery heat up during the charging process.
Warning!
The charger is not a toy. Only use the charger supplied.
•
The battery may only be charged by or under the supervision of an adult.
•
The terminals must not be short-circuited.
•
The charger must be checked regularly for damage to the cable, plug, housing and other
•
parts. If any damage is found, the charger must not be used until the damage has been
repaired.
• Let the model cool off sufficiently after each use before putting it back into operation.
When using an additional batteries let it cool off for minimum 15 minutes until the
model is operated again. Overheating can damage the electronics or may result in fire.
• Always disconnect the model from the charger immediately after charging. Always
disconnect the charger from the power supply immediately after disconnecting the
model. Inserting the rechargeable model or charger after charging will result in damage
tothe model, charger or the power supply (fire hazard).
•
Use the charger only in dry rooms.
Functions
1
Ignition lock
Starting model
Put key in the ignition (1) and turn.
2
Shift Lever:
Forward:
Press the "Forward-backward switch" on the "Forward" position. Press the "Foot
pedal", the model drives forward.
Stop:
The model will brake automatically, when your child's foot remove from the "Foot
pedal". Press the "Forward-backward switch" in the middle.
Reverse:
Press the "Forward-backward switch" on the "Backward" position. Press the "Foot
pedal", the model drives backward.
IMPORTANT!
Always stop vehicle when changing the speed or direction to avoid damage the gears
and motor.
3
Sounds button
4
Foot pedal
Applies power (speed) to the vehicle.
● To move the car, press the pedal down.
● To brake or slow down, release pressure from the pedal.
5
Light button
With the switch to turn on the lights ON or OFF
Description of the functions on the transmitter
This transmitter has following function:
1.
Forward
2.
Backward
3.
left / right
4.
Speed adjustment with delay (Approx. 3 sec.)
5.
Gear indicator
6.
Stop (emergency stop function)
7.
Power LED
Fitting the transmitter batteries
Open the battery compartment cover on the back of the transmitter and put 2 AAA batteries making
sure that it is corectly put in. Then close the cover.
Binding of transmitter and model
If the model does not respond to the transmitter, press the forwards (1) and backwards (2) buttons
for about 3 sec until the Power LED (7) flashes. Now switch on the model, the Power LED is lit
continuously.If this does not work, repeat the process.
Werbung
