Comet CPS 45 E Bedienungsanleitung Seite 36

6.14. SPECIFIC INSTRUCTIONS FOR THE USE OF
MODEL AC 230V
The AC 230V machine may be turned on only if the
voltage indicated on the tag corresponds with the
available voltage and that the electrical outlet is
grounded (earthed).
Do not damage the feed cable; do not crush or pull
on it.
• ATTENTION Make sure that the power cable does
not come into contact with the rotary brushes.
• ATTENTION - The AC 230V machine has parts,
which are connected to the current; contact with
these could cause grave injuries or even death.
- Before executing any type of operation on the ma-
chine always disconnect it from the electrical source.
- Never touch electric cables that are defective or
worn.
- Before gaining access to the electrical system it is
always necessary to disconnect the machine from
the electrical source by removing the plug from the
socket-outlet.
- In the case of defective, damaged, or cracked electric
cables, replace immediately with authentic replace-
ment parts.
- The network of connections must be protected from
water spray.
- The patch cord for the connection of the machine
to the mains power must conforms to current
safety rules.
- The electrical system to which the machine is con-
nected must be equipped with a cutout box.
- It is absolutely forbidden to use the machine in prox-
imity to swimming pools or stretches of water.
• EMERGENCY SITUATIONS
In case of emergency:
- Immediately disconnect the machine from the
power mains.
- Immediately apply proper first-aid.
If an accident should occur the machine must not be
put into operation until a technician authorized by
the manufacturer has examined it.
7. MAINTENANCE
• Switch OFF the ON-OFF main switch, and Discon-
nect the Anderson connector of the battery wiring
from the Anderson connector of the machine wiring
(Foto B-17)(Foto B-18).
☞ All work on the electrical system as well as all main-
tenance and repair operations (especially those not
explicitly described in this manual) should be carried
out only by authorized service centers or by special-
ized technical personnel who are experts in the sector
and in the pertinent safety regulations.
Performing regular maintenance on the machine, and
carefully following the manufacturer's instructions,
is the best guarantee for obtaining the best perfor-
mances and extended machine service life.
7.1. TANKS
Drain the two tanks as described in the relative sections.
Remove any solid dirt by filling and draining the tanks
until all dirt has been eliminated: use a washing hose
or similar tool to do this.
• Water hotter than 50°, a high-pressure cleaner
or excessively powerful sprays may damage the
tanks and the machine.
Leave the plugs of the tanks open (only while the ma-
chine is not being used) so that they can dry and thus
prevent the formation of foul odors.
7.2. SOLUTION FILTER CLEANING
Remove the transparent cap (Foto E-36) then remove
the metal strainer.
Clean them, reinstall the metal strainer in its seat and
close the water filter screwing the transparent cap.
7.3. SUCTION HOSE
Detach the suction hose from the squeegee (Foto
H-27) . Now you can wash the hose and remove any
obstructions.
Firmly insert the hose on the squeegee body.
7.4. SQUEEGEE
• Do not handle the squeegee with bare hands: wear
gloves and any safety clothing needed to carry out
the operation.
Detach the squeegee from the machine and clean it
under running water using a sponge or a brush.
Check the efficiency and the wear on the strips in con-
tact with the floor. They are designed to scrape the
film of detergent and water on the floor and to isolate
that portion of the surface to enhance the vacuum of
the suction motor: this ensures that the machine will
dry very efficiently. Working constantly in this manner
tends to round or to deteriorate the sharp edge of the
strip, thus reducing drying efficiently. This is why the
squeegee strips must be replaced.
To replace the worn blades, follow the instructions in
the relative section. Turn the blades around to wear
down the other sharp corners or to install new ones.
7.5. ACCESSORIES
Remove and clean the brush or the abrasive pad disk.
• To avoid damaging the floor and the machine, care-
fully check if foreign matter, such as metallic parts, screws,
chips, cords or similar items, has become jammed.
Check that the brushes are flat as they work on the
surface (check for any irregular wear on the brushes
36