Bosch CompactTube 400 Originalbetriebsanleitung Seite 27

(e.g. a hex key). The battery will be unlocked and fall
into the safety restraint (23).
Note: When removing the eBike battery, hold it firmly in your
hand.
❷ Press the safety restraint (23). Hold the battery firmly
in place if the battery is sliding out of the bicycle
frame. Then remove the battery.
Note: The unlocking element may vary from the image and
may be a manufacturer-specific solution. Read the operating
instructions of the eBike manufacturer.
Note: As a result of varying designs, the battery may need
to be inserted and removed using a different method. Read
the operating instructions of the eBike manufacturer.
Inserting the CompactTube battery (axial) (see figure H)
❶ To insert the CompactTube battery (21), insert it into
the frame with the socket for the charging con-
nector (5) facing upwards until you hear the battery
click into place in the safety restraint (23). Ensure that
the battery is aligned correctly.
❷ Slide the battery into the battery lock (2) until you
hear it click into place in the battery lock (2).
❸ Then remove the key (1) from the battery lock (2).
Always remove the key (1) from the battery lock (2) after
locking it. This prevents both the key from falling out and the
eBike battery from being removed by unauthorised third
parties when the eBike is not in use.
Inserting and Removing the PowerPack Battery
(see figure I)
In order to insert the battery, the key (1) must not be inser-
ted in the battery lock (2).
❶ To insert the PowerPack battery (15), place it so that
its contacts are in the lower holder (16) on the eBike.
❷ Twist it into the upper holder (14) as far as possible
until you hear it click into place.
Always remove the key (1) from the battery lock (2) after
locking it. This prevents both the key from falling out and the
eBike battery from being removed by unauthorised third
parties when the eBike is not in use.
❶ To remove the PowerPack battery (15), switch it off
and open the battery lock (2) using the key (1).
❷ Twist the battery out of the upper holder (14) and pull
it out of the lower holder (16).
Inserting and removing the rack-mounted battery
(see figure J)
In order for the battery to be inserted, the battery lock (2)
must be locked. The key (1) must not be inserted in the bat-
tery lock (2).
To insert the battery (27), slide its contacts into the
holder (26) until you hear it click into place.
To remove the battery (27), switch it off and open the bat-
tery lock using the key (1) ❶.
Pull the battery out of the holder (26) ❷.
Bosch eBike Systems
Operation
Start-up
Use only original Bosch eBike batteries from the sys-
u
tem generation the smart system, which the manufac-
turer has approved for your eBike. Using other eBike
batteries can lead to injuries and pose a fire hazard.
Bosch accepts no liability or warranty claims if other
eBike batteries are used.
Switching on/off
Switching on the eBike battery is one way to switch on the
eBike. To do this, read and follow the instructions in the op-
erating manuals for the drive unit and operating unit.
Before switching on the eBike battery, i.e. the eBike, make
sure that the battery lock (2) is locked.
To switch on the eBike battery, press the on/off button (7).
Do not use any sharp or pointed objects to press the button.
To switch off the eBike battery, press the on/off button (7)
again. This will also switch the eBike off.
If no power is drawn from the drive for about 10 minutes
(e.g. because the eBike is not moving) and no button is
pressed on the on-board computer or the operating unit of
the eBike, the eBike will switch off automatically.
The eBike battery is protected against deep discharge, over-
loading, overheating and short-circuiting by the "Battery
Management System (BMS)". In the event of danger, a pro-
tective circuit switches the eBike battery off automatically.
Recommendations for Optimal Handling of the
eBike Battery
The service life of the eBike battery can be extended if it is
looked after well and especially if it is stored at the correct
temperature.
As it ages, however, the capacity of the eBike battery will di-
minish, even with good care.
A significantly reduced operating time after charging indic-
ates that the eBike battery has deteriorated. The eBike bat-
tery should be replaced.
Recharging the eBike Battery Before and During Storage
When you are not going to use the eBike battery for an exten-
ded period (longer than three months), store it at a state of
charge of around 30 % to 60 % (when two to three of the
LEDs on the battery charge indicator (6) are lit).
Check the state of charge after six months. If only one of the
LEDs on the battery charge indicator (6) is lit, charge the
eBike battery back up to around 30 % to 60 %.
Note: If the eBike battery is stored with no charge for an ex-
tended period of time, it may become damaged despite the
English – 5
If a fault is detected in the
eBike battery, two of the
LEDs on the battery charge
indicator (6) will flash. Con-
tact an authorised bicycle
dealer if this happens.
0 275 007 3PX | (19.06.2023)