VONROC TS502AC Bersetzung Der Originalbetriebsanleitung Seite 10

EN
Saw blades that do not match the mounting
hardware of the saw will run off-centre, causing
loss of control.
h) Never use damaged or incorrect saw blade
mounting means such as flanges, saw blade
washers, bolts or nuts. These mounting means
were specially designed for your saw, for safe
operation and optimum performance.
i) Never stand on the table saw, do not use it as a
stepping stool. Serious injury could occur if the
tool is tipped or if the cutting tool is accidentally
contacted.
j) Make sure that the saw blade is installed to
rotate in the proper direction. Do not use grind-
ing wheels, wire brushes, or abrasive wheels
on a table saw. Improper saw blade installation
or use of accessories not recommended may
cause serious injury
ATTENTION! When using electric tools to protect
against electric shock, injury and fire the following
basic safety measures must be observed. Make
sure to read all of these instructions before you
use this power tool, keep the safety booklet and
preserve it well for later reference.
1. Always keep your workplace clean and tidy.
• An untidy workplace can lead to unwanted
accidents.
2. Consider environmental influences.
• Do not expose the power tool to rain.
• Do not use the power tool in a damp or wet
environment.
• Make sure that your working space has suffi-
cient lighting.
• Do not use the power tool in areas where there
is a fire or explosive hazard.
3. To protect yourself from an electric shock.
• Avoid body contact with grounded parts (e.g.
pipes, radiators, electric stoves, refrigerators
etc.).
4. Keep other people away
• Keep other people away especially children, do
not let them touch your power tool or cable and
keep the children away from your working area.
5. Store the unused power tools safely.
• Unused power tools should be locked up or stored
in a place that is dry and out of reach of children.
6. Do not overload your power tool.
• You work better and safer in the specified power
range.
10
7. Use the correct power tool.
• Do not use low-power machines for heavy work
• Do not use the power tool for purposes that they
are not intended for. For example you cannot cut
tree limbs or a log of wood using a hand saw.
8. Wear suitable clothing.
• Do not wear loose clothing or jewelry; they can
be caught in the moving parts.
• When working outdoors non-skid footwear is
recommended.
• For long hair, wear a hairnet.
9. Use protective equipment.
• Wear protective goggles
• When doing work that generates dust, use a
breathing mask.
10. Connect the vacuum device
• If connection to the vacuum and catcher are
available then you know that these are connec-
ted and properly used.
11. Do not use the cable for purposes that it is not
intended for.
• Do not use the cable to the connector to pull it
out of the socket. Protect the cable from heat,
oil and sharp edges.
12. Secure the power tool.
• Use clamps or a vice to hold the power tool. It is
safer than holding it with your hand.
13. Avoid an abnormal posture.
• It ensures stability and keeps you balanced at
all times.
14. Keep and maintain tools with care.
• Keep the cutting tools sharp and clean, this
ensures that you work better and that it is as
safe as possible.
• Follow the lubricating and tool changing in-
structions.
• Check the connection cable of the power tool
regularly and let a qualified expert repair any
damages.
• Check the extension cables regularly and replace
them if they are damaged.
• Keep the handles clean, dry and free of grease
and oil.
15. Unplug the power tool from the power outlet.
• When you are not using the power tool, when
you conduct maintenance and when you chan-
ge your tools such as blades, drills and cutters.
16. Do not leave the key inside the tool.
• Before switching it on, make sure that keys and
setup tools have been cleared
17. Avoid unintentionally switching the power tool on.
WWW.VONROC.COM