Technical Data; Drill Safety Warnings - AEG BSB18G4-0 Originalbetriebsanleitung

TECHNICAL DATA

Type
Production code
Battery voltage
No-load speed 1st gear
No-load speed 2nd gear
Rate of percussion under load, 1st gear
Rate of percussion under load, 2st gear
Drilling capacity in steel
Drilling capacity in wood
Drilling capacity in brick and tile
Wood screws (without pre-drilling)
Torque max
Drill chuck range
Weight without battery
Weight according EPTA-Procedure 01/2014 (L1820S)
Recommended ambient operating temperature
Recommended battery types
Recommended charger
Noise Information: Measured values determined according to
EN 62841.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level / Uncertainty K
Sound power level / Uncertainty K
Wear ear protectors!
Vibration Information: Total vibration values (vector sum in the
three axes) determined according to EN 62841.
Vibration emission value a / Uncertainty K
h
Drilling into metal
Drilling into concrete
WARNING
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test
given in EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration and noise emission may differ. This may significantly
increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration and/or noise such as: maintain the tool and the
accessories, keep the hands warm, organization of work patterns.
WARNING
Read all safety warnings, instructions,
illustrations and specifications provided with this power
tool. Failure to follow all instructions listed below may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.

DRILL SAFETY WARNINGS

Safety instructions for all operations
Wear ear protectors when impact drilling. Exposure to noise
can cause hearing loss.
Hold the power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory may
contact hidden wiring. Cutting accessory contacting a „live"
wire may make exposed metal parts of the power tool „live" and
could give the operator an electric shock.
Safety instructions when using long drill bits
Never operate at higher speed than the maximum speed
rating of the drill bit. At higher speeds, the bit is likely to bend
if allowed to rotate freely without contacting the workpiece,
resulting in personal injury.
Always start drilling at low speed and with the bit tip in
20
470 487 - BSB18G4.indd 20 470 487 - BSB18G4.indd 20
Cordless percussion drill/driver
4811 66 01 XXXXXX MJJJJ
L1840R, L1820R, L1820S
100,5 dB(A) / 5 dB(A)
contact with the workpiece. At higher speeds, the bit is likely to
bend if allowed to rotate freely without contacting the workpiece,
resulting in personal injury.
Apply pressure only in direct line with the bit and do not
apply excessive pressure. Bits can bend causing breakage or
loss of control, resulting in personal injury.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when
working with the machine. The use of protective clothing is
recommended, such as dust mask, protective gloves, sturdy
non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to
health. Do not inhale the dust. Wear a suitable dust protection
mask.
Do not machine any materials that present a danger to health
(e.g. asbestos).
Switch the device off immediately if the insertion tool stalls! Do
not switch the device on again while the insertion tool is stalled,
as doing so could trigger a sudden recoil with a high reactive
force. Determine why the insertion tool stalled and rectify this,
paying heed to the safety instructions.
ENGLISH
BSB18G4
18 V
500 min
-1
1800 min
-1
0 - 8000 min
-1
0 - 28800 min
-1
13 mm
54 mm
13 mm
6 mm
60 Nm
2 - 13 mm
1,3 kg
1,7 kg
-18...+50 °C
BL1218, BL18S
89,5 dB(A) / 5 dB(A)
1,6 m/s / 1,5 m/s
2 2
8,1 m/s / 1,5 m/s
2 2
03.02.2021 09:34:32 03.02.2021 09:34:32