Residual Risks - Black & Decker MTSA2 Originalanweisungen

e. Do not use a battery pack or tool that is damaged
or modified. Damaged or modified batteries may
exhibit unpredictable behaviour resulting in fire,
explosion or risk of injury.
f. Do not expose a battery pack or tool to fire
or excessive temperature. Exposure to fire or
temperature above 130 °C may cause explosion.
g. Follow all charging instructions and do not charge
the battery pack or tool outside the temperature
range specified in the instructions. Charging
improperly or at temperatures outside the specified
range may damage the battery and increase the
risk of fire.
6. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power tool
is maintained.
b. Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers (only
used for battery tools).
Safety instructions for sanders
Š Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
@
may lead to loss of control.
Warning! Contact with or inhalation of dusts arising
from sanding applications may endanger the health
of the operator and possible bystanders. Wear a dust
mask specifically designed for protection against dust
and fumes and ensure that persons within or entering
the work area are also protected.
Additional safety instructions for sanders
Š Thoroughly remove all dust after sanding.
Š Take special care when sanding paint which is possibly
lead based or when sanding some woods and metal which
may produce toxic dust:
Do not let children or pregnant women enter the
-
work area.
Do not eat, drink or smoke in the work area.
-
Dispose of dust particles and any other debris safely.
-
Š The intended use is described in this instruction manual.
The use of any accessory or attachment or performance of
any operation with this tool other than those recommended
in this instruction manual may present a risk of personal
injury and/or damage to property.

Residual risks

The following risks are inherent to the use of saws:
Š Injuries caused by touching the rotating parts.
(Original instructions)
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks cannot be avoided. These are:
Š Impairment of hearing.
Š Risk of accidents caused by the uncovered parts of the
rotating saw blade.
Š Risk of injury when changing the blade.
Š Risk of squeezing fingers when opening the guards.
Š Health hazards caused by breathing dust developed when
sawing wood, especially oak, beech and MDF.
Safety of others
Š This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the tool by a person responsible for their safety.
Š Children should be supervised to ensure that they do not
play with the appliance.
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured in
accordance with a standard test method provided by EN62841
and may be used for comparing one tool with another. The
declared vibration emission value may also be used in a
@
preliminary assessment of exposure.
Warning! The vibration emission value during actual
use of the power tool can differ from the declared
value depending on the ways in which the tool is
used. The vibration level may increase above the
level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Labels on tool
The following symbols are shown on the tool along with the
date code:
:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
n
Do not stare at operating lamp
Additional safety instructions for batteries and
chargers
Batteries
Š Never attempt to open for any reason.
Š Do not expose the battery to water.
ENGLISH
5