Makita DUR365U Betriebsanleitung Seite 14

To reverse the rotation, tap the reverse button and pull the
trigger when the tool's head is stopped. The power lamp
starts blinking, and the tool's head rotates in reverse
direction when you pull the switch trigger.
To return to regular rotation, release the trigger and wait
until the tool's head stops.
NOTE:
• During the reverse rotation, the tool operates only for a
short period of time and then automatically stops.
• Once the tool is stopped, the rotation returns to regular
direction when you start the tool again.
• If you tap the reverse button while the tool's head is still
rotating, the tool comes to stop and to be ready for
reverse rotation.
Nylon cutting head (optional accessory)
NOTICE:
• The bump feed will not operate properly if the head is
not rotating.
The nylon cutting head is a dual string trimmer head
provided with a bump & feed mechanism.
To cause the nylon cord to feed out, the cutting head
should be bumped against the ground while rotating.
(Fig. 11)
NOTE:
If the nylon cord does not feed out while bumping the
head, rewind/replace the nylon cord by following the
procedures described under "Maintenance."
ASSEMBLY
WARNING:
• Always be sure that the tool is switched off and
battery cartridge is removed before carrying out
any work on the tool. Failure to switch off and remove
the battery cartridge may result in serious personal
injury from accidental start-up.
• Never start the tool unless it is completely
assembled. Operation of the tool in a partially
assembled state may result in serious personal injury
from accidental start-up.
Installing the handle
Insert the shaft of the handle into the grip. Align the screw
hole in the grip with the one in the shaft. Tighten the screw
securely. (Fig. 12)
Place handle between handle clamp and handle holder.
Adjust the handle to an angle that provides a comfortable
working position and then secure by firmly hand-
tightening knob. (Fig. 13)
Installing the guard
WARNING:
• Never use the tool without the guard illustrated in
place. Failure to do so can cause serious personal
injury.
• Always use the tool with the approved combination of
the safety equipments. Otherwise contact with a cutting
tool may cause serious injury.
• Permitted combination for the cutting tool and the
guard may differ from country to country. Follow your
region's regulations.
14
For metal blade (Fig. 14 & 15)
For nylon cutting head or plastic blade
CAUTION:
• Take care not to injure yourself on the cutter for cutting
the nylon cord when installing nylon cutting head or
plastic blade. (Fig. 16)
Align the clamp on the pipe with the protector. And tighten
them with bolts. (Fig. 17)
Installing the metal blade (optional
accessory)
WARNING:
• The outside diameter of the metal blade must be
230 mm. Never use any blade exceeding 230 mm in
outside diameter.
CAUTION:
• The metal blade must be well polished, free of cracks
or breakage. Polish or replace the metal blade every
three hours of operation.
• Always wear gloves when handling the metal blade.
• Always attach the blade cover when the tool is not in
use or is being transported.
• The metal blade-fastening nut (with spring washer)
wears out in course of time. If there appears any wear
or deformation on the spring washer, replace the nut.
Ask your local authorized service center to order it.
• Replace the cup in case of crack or breakage due to
attrition.
NOTICE:
• Be sure to use genuine Makita metal blade.
Turn the tool upside down so that you can replace the
metal blade easily.
Mount the metal blade onto the shaft so that the guide of
the receive washer fits in the arbor hole in the metal
blade. Install the clamp washer and secure the metal
blade with the hex nut with 13 to 23 Nm of tightening
torque during holding the receive washer with hex
wrench. (Fig. 18)
To dismount the metal blade, insert the hex wrench
through the hole on the protector cover and the gear case.
Rotate the receive washer until it is locked with the hex
wrench. Loosen the hex nut (left-hand thread) with the
socket wrench and remove the nut, clamp washer and
hex wrench. (Fig. 19)
Make sure that the blade is the left way up. (Fig. 20)
Installing nylon cutting head or plastic
blade (optional accessory)
CAUTION:
• If the nylon cutting head/plastic blade accidentally
impacts a rock or hard object during operation,
stop the tool and inspect for any damage. If the
nylon cutting head/plastic blade is damaged,
replace it immediately. Use of a damaged cutting tool
could result in serious personal injury.
NOTICE:
• Be sure to use genuine Makita nylon cutting head/
plastic blade.
Turn the tool upside down so that you can replace the
nylon cutting head easily.