Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Automat
tic battery savi
This
function switc
move
e the rotary sw
7.1 Vo
oltage meas
Do not mea
occur.
Always be ca
fingers behin
terminals wh
•
Conn
nect the black t
•
Set t
the rotary sele
meas
surements
•
Conn
nect the test le
•
The
measured valu
•
Whe
n desired, sele
•
Press
s the Hz/DUT
(freq
quency range 4
Notes:
•
F
For DC-measur
i
ndicated value
•
W
When the meas
"OL". Select a h
"
7.2 Cu
urrent meas
Do not measu
Current measu
10A jack. Whe
followed by a
Always be car
fingers behind
•
For
measuremen
black
k lead to the "C
•
For
measuremen
lead
to the "COM"
•
Set t
the rotary sele
10A
jack is not fus
•
Set t
the rotary sele
•
Whe
n the range is
appr
ropriate range.
•
Selec
ct the AC or DC
curre
ent).
•
Conn
nect the test pr
•
Read
d the measured
•
Whe
n desired, sele
•
Press
s the Hz/DUT
(freq
quency range 4
Notes:
•
For DC-current
F
t
the indicated va
•
T
The 400mA-ran
r
range is not pr
•
When measurin
W
b
break between
28.06.20
010
ing mode:
hes the meter
to battery sav
witch to reactiv
vate the meter
surements
sure circuits
in a CATIV en
areful when wo
orking with volt
nd the probe ba
arriers at all tim
hen the meter i
is linked to a c
test lead to the
e COM jack an
ctor to
V an
nd press the FU
or DC measure
ements
eads to the circ
cuit under test.
ue appears on t
the display.
ect a range ma
nually with the
TY button to se
ee the frequenc
40Hz~400Hz).
Press again to
rements: when
n a negative po
e is preceded by
y a "-" sign.
sured value is
higher than th
higher range.
surements
ure current in c
circuits with vo
urements: 400
0mA jack max.
en measuring c
currents up to
10 minutes br
eak between 2
reful when wor
king with volta
d the probe bar
rriers at all tim
ts up to 400m
mA: connect th
COM" jack.
ts up to 10A:
: connect the r
jack.
ctor to 10A
for measurem
se protected.
ctor to 400mA
A
unknown, alwa
ays select the
C range with th
he FUNC. butt
robes in series
with the circu
d value from th
he display.
ect a range ma
nually with the
TY button to se
ee the frequenc
40Hz~400Hz).
Press again to
measurement
ts, when a neg
alue is precede
ed by a "-" sign
nge is protecte
ed against over
rotected.
ng up to 10A, m
max. 15s conti
2 measureme
nts.
DVM14
00
ving mode after
.
nvironment o
tages above 60
mes during me
ircuit which is
nd the red test
UNC. button to
.
.
e RANGE butto
cy or duty cycle
o return to volta
olarity is presen
e selected rang
ltages > 600V
400mA; for m
10A, max. 15s
2 measurement
ages above 60V
mes during mea
he red test lead
ed test lead to
ments up to 10A
for measu
rements up to
highest possib
ton (
= alter
it.
e RANGE butto
cy or duty cycle
o return to volta
ative polarity i
n.
r-current with a
nuous measur
8
r 15 min. Push
any button or
or where volta
ages > 600V
0Vdc or 30Vac
rms. Keep you
easurement. Do
o not touch un
being tested.
lead to the
HzVΩ jack.
o choose betwe
een AC
on.
e of the measu
ured voltage
age display.
nt at the red te
est lead, the
ge limit, the di
splay will show
measurements
up to 10A use
s continuous m
measurement
ts.
Vdc or 30Vac r
rms. Keep your
asurement.
d to the "mA°C
C" jack and the
the "10A" jac
ck and the blac
A on the 10A ja
ack. Warning
400mA on the
e mA°C jack.
ble range and lo
ower to the
nating current,
,
on.
e of the measu
ured voltage
age display.
s present at th
he red test lead
an F500mA 60
0V fuse; the 1
rement followed
d by a 10 minu
Rev
v. 02
r
may
ur
used
w
the
r
e
ck
: the
= direct
d,
0A-
utes
©Vellema
n nv
Werbung
