Operation - EINHELL 43.002.95 Originalbetriebsanleitung

5.4 Precision adjustment of the stop rail
(Fig. 7/8)
•
Lower the machine head (4) and fasten in
place with the safety pin (16).
•
Fasten the turntable (8) in 0° position.
•
Place the 90° stop angle (a) between the bla-
de (5) and the stop rail (7).
•
Slacken the adjustment screws (28), set the
stop rail (7) to 90° in relation to the saw blade
(5) and retighten the adjustment screws (28).
5.5 Precision adjustment of the stop for 90°
cross-cuts (Fig. 8-10)
•
Lower the machine head (4) and fix with the
lock pin (16).
•
Slacken the tightening screw (12).
•
Place the stop angle (a) between the saw
blade (5) and the rotary table (8).
•
Slacken the counter nut (29) and adjust the
setting screw (18) until the angle between the
saw blade (5) and the rotary table (8) equals
90°.
•
Re-tighten the counter nut (29) to fix the ma-
chine in this setting.
•
Finally, check the position of the angle indica-
tor (11). If necessary, release the pointer with
a crosstip screwdriver, move to the 0° position
of the angle scale (15) and retighten the hol-
ding screw.
•
No stop angle included.
5.6 Precision adjustment of the stop for 45°
mitre cuts (Fig. 8/12)
•
Lower the machine head (4) and fix with the
lock pin (16).
•
Fix the rotary table (8) in 0° position.
•
Undo the tightening screw (12) and use the
handle (2) to tilt the machine head (4) to the
left until it coincides at 45°.
•
Place the 45° stop angle (b) between the saw
blade (5) and the rotary table (8).
•
Slacken the counter nut (30) and adjust the
setting screw (19) until the angle between the
saw (5) and the rotary table (8) equals exactly
45°.
•
No stop angle included.
Anl_TH_MS_2112_SPK1.indb 22 Anl_TH_MS_2112_SPK1.indb 22
GB

6. Operation

6.1 Crosscut 90° and turntable 0° (Fig. 1)
•
Press the main switch (3) to turn on the saw.
•
Important. Place the material for sawing firmly
on the machine surface, to prevent it from
moving during the sawing process.
•
After switching on the saw, wait for the blade
(5) to reach its maximum speed.
•
Press the release lever (1) sideways and,
using the handle (2), apply steady and light
downward pressure to move the machine
head through the workpiece.
•
When the cut is completed, return the machi-
ne to its top parking position and let go of the
On/Off switch.
•
Caution! A return spring causes the machine
head to rise automatically at the end of the
cut. Do not let go of the handle (2) as soon as
the cut is completed but steady the machine
head and allow it to rise slowly.
6.2 90° cross-cuts and 0°-45° rotary table
(Fig. 10)
The crosscut saw can be used to make right and
left angular cuts of 0°- 45° in relation to the stop
rail.
•
Lift the machine head (4) to its top position.
•
Release the turntable (8) by slackening the
locking grip (10).
•
Using the handle (2), set the turntable (8) to
the desired angle, i.e. the marking on the turn-
table must coincide with the desired angular
setting (17) on the stationary base plate (9).
•
Re-tighten the locking handle (10) in order to
fix the rotary table (8) in position.
•
Make the cut as described in Section 6.1).
6.3 Mitre cuts 0°-45° and rotary table 0°
(Fig. 8/11)
The crosscut saw can be used to make miter cuts
of 0° - 45° in relation to the work face.
•
Lift the machine head (4) to its top position.
•
Fix the rotary table (8) in 0° position.
•
Undo the tightening screw (12) and use the
handle (2) to tilt the machine head (4) to the
left until the pointer (11) coincides with the
required angle value (15).
•
Re-tighten the locking nut (12) and make the
cut as described in Section 6.1).
- 22 -
06.03.14 11:07 06.03.14 11:07