Operation - EINHELL 43.008.25 Originalbetriebsanleitung

support (26).
•
Mount the workpiece support (10) on the
fixed saw table (18) and tighten the appropri-
ate locking screw (26) (Figure 4).
•
Mount the second workpiece support (10) on
the opposite side of the saw and secure with
the appropriate locking screw (26).
•
When the locking screw (21) is loosened, you
can tilt the machine head (4) to the left by up
to 45°.
•
To ensure that the saw is standing securely,
adjust the adjustable foot (13) by turning it so
that the saw stands in a horizontal and firm
position.
5.3 Precision adjustment of the stop for cros-
scut 90° (Fig. 6-8)
•
Fasten the turntable (17) in 0° position.
•
Undo the locking screw (21) and move the
machine head (4) all the way to the right using
the handle (1).
•
Place the 90° angular stop (a) between the
blade (7) and the turntable (17).
•
Adjust the adjustment screw (29) until the
angle between the blade (7) and the turntable
(17) equals 90°.
•
Finally check the position of the pointer (20)
on the scale (19). If necessary, undo the poin-
ter (20) with a Philips screwdriver, set it to the
0° position on the scale (19) and retighten the
retainer screw.
•
No stop angle included.
5.4 Precision adjustment of the stop for miter
cut 45° (Fig. 1, 7, 9)
•
Fasten the turntable (17) in 0° position.
•
Undo the locking screw (21) and move the
machine head (4) all the way to the left using
the handle (1), until it coincides at 45°.
•
Place the 45° stop angle (b) between the bla-
de (7) and the turntable (17).
•
Adjust the adjustment screw (30) so that the
angle between the blade (7) and the turntable
(17) equals exactly 45°.
•
No stop angle included.
5.5 Adjusting the miter angle on the machine
head (Fig. 2, 12-13)
•
Undo the locking screw (21).
•
Hold the machine head (4) by the handle (1).
•
After pulling the button (33), the machine
head can be tipped infinitely as well as to se-
veral locking points.
•
Angles to the left: 0-45°
•
Angles to the right: 0-45°
Anl_TC_SM_2534_Dual_SPK9.indb 25 Anl_TC_SM_2534_Dual_SPK9.indb 25
GB
•
Re-tighten the locking screw (21).
5.6 Adjusting the movable stop rails
(Fig. 1, 10-14)
•
Caution! This saw is equipped with movable
stop rails (34) that are screwed to the fixed
stop rail (11).
•
For carrying out angle and miter cuts the mo-
vable stop rails must be adjusted to prevent a
collision with the saw blade.
•
For miter and angle cuts to the left, the left
stop rail must be moved outwards. For angle
cuts to the right, the right stop rail must be
moved outwards. Undo the locking screws on
the movable stop rails and pull the rails back
so far that a collision with the saw blade can
be ruled out. Prior to every cut retighten the
locking screws of the stop rails.
•
For miter cuts and double miter cuts with the
saw head tilted to the right, the right stop rail
must be removed completely. Important! In
this case the maximum permissible workpie-
ce height is reduced (see 4. Technical data).
•
Always fasten the movable stop rails back to
the equipment again after you have comple-
ted your work.
•
The stop rails must always remain together
with the equipment. A removed stop rail will
impair the operational safety of the equip-
ment.

6. Operation

6.1 Cross cut 90° and turntable 0°
(Fig. 1-3, 11)
For cutting widths up to approx. 100 mm it is
possible to fi x the saw's drag function with the
locking screw for drag guide (24) in rear position.
If the cutting width exceeds 100 mm, you must
ensure that the locking screw for drag guide (24)
is slackened and that the machine head (4) can
be moved.
•
Move the machine head (4) to its upper posi-
tion.
•
Use the handle (1) to push back the machine
head (4) and fix it in this position if required
(dependent on the cutting width).
•
Place the piece of wood to be cut at the stop
rail (11) and on the turntable (17).
•
Lock the material with the clamping device
(8) on the fixed saw table (18) to prevent the
material from moving during the cutting ope-
ration.
- 25 -
02.08.2018 08:53:19 02.08.2018 08:53:19