Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
BTL5-A/C/E/G _ _ -M _ _ _ _ -P-S32/KA _ _
Micropulse Transducer in a Profile Housing
7
Technical data
7.1
Accuracy
The specifications are typical values for BTL5-A/C/E/G... at
24 V DC and room temperature, with a nominal length of
500 mm in conjunction with the BTL5-P-3800-2,
BTL5-P-4500-1, BTL5-P-5500-2
BTL6-A-3801-2
, BTL5-F-2814-1S, BTL5-T-2814-1S,
1)
BTL5-M-2814-1S or BTL5-N-2814-1S magnet.
The BTL is fully operational immediately, with full accuracy
after warm-up.
For special versions, other technical data may
apply.
Special versions are indicated by the suffix -SA
on the part label.
Resolution
BTL5-A/G...
BTL5-C/E...
Reproducibility
Sampling rate f
Standard
Non-linearity with a constant distance
between the magnet and profile
Nominal length ≤ 500 mm
Nominal length > 500 mm
Temperature coefficient
Voltage output:
[150 µV/K + (5 ppm/K * P * U/NL)] * ΔT
Current output:
[0.6 µA/K + (10 ppm/K * P * I/NL)] * ΔT
Max. detectable velocity
7.2
Ambient conditions
Operating temperature
Storage temperature
Relative humidity
Shock rating
per EN 60068-2-27
2)
Continuous shock
per EN 60068-2-29
2)
Vibration
per EN 60068-2-6
2)
Degree of protection per
IEC 60529
(when attached)
12
english
, BTL6-A-3800-2
,
1)
1)
≤ ±0.1 mV
≤ ±0.16 µA
≤ ±6 µm
1 kHz
±100 µm
±0.02 % FS
10 m/s
-40°C to +85°C
-40°C to +100°C
< 90%, non-condensing
100 g/6 ms
100 g/2 ms
12 g, 10 to 2000 Hz
IP67
7.3
Supply voltage (external)
Voltage, stabilized
BTL5-_1...
BTL5-_2...
Ripple
Current draw
Inrush current
Reverse polarity protection
Overvoltage protection
Dielectric strength
(GND to housing)
7.4
Output
BTL5-A... Output voltage
Load current
Ripple
BTL5-C... Output current
Load resistance
BTL5-E... Output current
Load resistance
BTL5-G... Output voltage
Load current
Ripple
7.5
Dimensions, weights, material
Housing height
Nominal length
Weight (depends on length)
Housing material
Cable diameter
3)
Permissible cable bending
radius
3)
Fixed routing
Movable
Cable material
3)
In the position range 0...20 mm, the specified linearity limit can be
1)
exceeded by ±50 µm.
Individual specifications as per Balluff factory standard
2)
For BTL5-...-KA_ _
3)
20 to 28 V DC
±14.7 to ±15.3 V DC
≤ 0.5 V
SS
≤ 150 mA
≤ 3 A/0.5 ms
Yes
Transzorb diodes
500 V DC
0...10/10...0 V
≤ 5 mA
≤ 5 mV
0...20/20...0 mA
≤ 500 ohms
4...20/20...4 mA
≤ 500 ohms
-10...10/10...-10 V
≤ 5 mA
≤ 5 mV
36.8 mm
50 to 4752 mm
Approx. 1.4 kg/m
Anodized aluminum
Max. 6.7 mm
≥ 34 mm
≥ 100 mm
PUR;
cULus 20549
80°C, 300 V,
internal wiring
Werbung
Inhaltsverzeichnis
