Makita DUR365PT4J Betriebsanleitung Seite 16

Rotate the receive washer until it is locked with the hex
wrench. Loosen the hex nut (left-hand thread) with the
socket wrench and remove the nut, clamp washer and
hex wrench. (Fig. 20)
Make sure that the blade is the left way up. (Fig. 21)
Installing nylon cutting head or plastic
blade (optional accessory)
CAUTION:
• If the nylon cutting head/plastic blade accidentally
impacts a rock or hard object during operation,
stop the tool and inspect for any damage. If the
nylon cutting head/plastic blade is damaged,
replace it immediately. Use of a damaged cutting tool
could result in serious personal injury.
NOTICE:
• Be sure to use genuine Makita nylon cutting head/
plastic blade.
Turn the tool upside down so that you can replace the
nylon cutting head easily.
Insert the hex wrench through the hole on the motor
housing and rotate the receive washer until it is locked
with the hex wrench. Place the nylon cutting head/plastic
blade onto the threaded spindle directly and tighten it by
turning it counterclockwise. Remove the hex wrench.
To remove the nylon cutting head/plastic blade, turn it
clockwise while holding the receive washer with the hex
wrench. (Fig. 22 & 23)
Hex wrench storage (Fig. 24)
When not in use, store the hex wrench as shown in the
figure to keep it from being lost.
OPERATION
Correct handling of tool
WARNING:
• Be extremely careful to maintain control of the tool
at all times. Do not allow the tool to be deflected
toward you or anyone in the work vicinity. Failure to
keep control of the tool could result in serious injury to
the bystander and the operator.
Correct posture
WARNING:
• Always hold the both grips firmly and position the
tool on your right-hand side so that the shaft of the
left handle is always in front of your body. Correct
positioning of the tool allows for maximum control and
will reduce the risk of serious personal injury caused by
kickback.
Fit the shoulder harness and hang the tool firmly on your
right side so that the shaft of the left handle is always
ahead of you. (Fig. 25)
Attachment of shoulder harness
Wear the shoulder harness on your left shoulder. Make
sure that the buckle cannot be taken off with pulling it off.
Hang the tool as shown. (Fig. 26)
The buckle is provided with a means of quick release.
Simply squeeze the sides of the buckle to release the tool.
(Fig. 27)
16
Adjustment of the hanger position and shoulder
harness
To change the hanger position, loosen the fixing screw on
the hanger with the supplied wrench and then move the
hanger and the cushion. The cushion can be moved
easily by twisting it.
MAINTENANCE
WARNING:
• Always be sure that the tool is switched off and
battery cartridge is removed before attempting to
perform inspection or maintenance on the tool.
Failure to switch off and remove the battery cartridge
may result in serious personal injury from accidental
start-up.
NOTICE:
Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
Replacing the nylon cord
WARNING:
• Use nylon cord with diameter specified in
"SPECIFICATIONS" only. Never use heavier line,
metal wire, rope or the like. Use recommended nylon
cord only, otherwise it may cause damage to the tool
and result in serious personal injury.
• Make sure that the cover of the nylon cutting head
is secured to the housing properly as described
below. Failure to properly secure the cover may cause
the nylon cutting head to fly apart resulting in serious
personal injury.
For 95-M10L
1. Press on the housing latches inward to lift off the
cover, then remove the spool. (Fig. 28)
2. Prepare approximately 3 m (9 ft) of new nylon cord.
Fold the new nylon cord with one end become
approximately 80 mm (3-1/8") longer than the other
end. Then hook the new nylon cord into the notch in
the center of the spool.
Wind both ends firmly around the spool in the direction
of the head rotation (left-hand direction indicated by
LH on the side of the spool). (Fig. 29)
3. Wind all but about 100 mm (3-15/16") of the cords,
leaving the ends temporarily hooked through a notch
on the side of the spool. (Fig. 30)
4. Mount the spool in the housing so that the grooves
and protrusions on the spool match up with those in
the housing. Keep the side with letters on the spool
visible on the top. Now, unhook the ends of the cord
from their temporary position and feed the cords
through the eyelets to come out of the housing.
(Fig. 31)
5. Align the protrusion on the underside of the cover with
the slots of the eyelets. Then push the cover firmly
onto the housing to secure it. (Fig. 32)
For B&F ECO4L
Take off cover from housing, pressing two latches which
are slotted section oppositely on side of housing. (Fig. 33)