Herunterladen Inhalt Inhalt Diese Seite drucken

Maintenance And Service; Maintenance And Cleaning - Bosch GCM 350-254 Professional Originalbetriebsanleitung

Vorschau ausblenden Andere Handbücher für GCM 350-254 Professional:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1
– Then retighten the lock nut of the stop screw (66).
If the angle indicators (41) and (5) are not in line with the
45° marks on the scale (4) following adjustment, first check
the 0° setting for the bevel angle and the angle indicators
once more. Then repeat the adjustment of the 45° bevel
angle.
Setting the Standard 45° Mitre Angle (right)
– Bring the power tool into the work position.
– Turn the saw table (18) to the 0° detent (25). The lever
(22) must be felt to engage in the detent.
– Remove the right adjustable fence (2).
– Swing the stop (42) all the way out
– Turn the right stop (3) until the standard 45° bevel angle
engages at the arrow mark.
– Loosen the clamping lever (7).
– Swing the tool arm left by the handle (12) until the stop
screw (67) lies on the stop (3).
Checking (see figure V1)
– Set an angle gauge to 135° and place it on the saw table
(18).
The leg of the angle gauge must be flush with the saw blade
(47) along its entire length.
Setting (see figure V2)
– Loosen the lock nut of the stop screw (67) with a com-
mercially available ring or open-ended spanner (10 mm).
– Turn the stop screw (67) as far in or out as needed until
the leg of the angle gauge is flush with the saw blade along
its entire length.
– Re-tighten the clamping lever (7).
– Then re-tighten the lock nut of the stop screw (67).
If the angle indicators (41) and (5) are not in line with the
45° marks on the scale (4) following adjustment, first check
the 0° setting for the bevel angle and the angle indicators
once more. Then repeat the adjustment of the 45° bevel
angle.
Aligning the scale for mitre angles
– Bring the power tool into the work position.
– Turn the saw table (18) to the 0° detent (25). The lever
(22) must be felt to engage in the detent.
Checking (see figure W1)
– Set an angle gauge to 90° and position it between the
fence (1) and the saw blade (47) on the saw table (18).
The leg of the angle gauge must be flush with the saw blade
(47) along its entire length.
Setting (see figure W2)
– Loosen all four set screws (68) using the hex key (4 mm)
and turn the saw table (18) together with the scale (26)
until the leg of the angle gauge is flush with the saw blade
along its entire length.
– Re-tighten the screws again.
If the angle indicator (24) is not aligned with the 0° mark on
the scale (26) following adjustment, loosen the screw (69)
using a cross-headed screwdriver and align the angle indic-
ator along the 0° mark.
Bosch Power Tools
Setting (see figure W2)
– Loosen all four set screws (68) with a cross-headed
screwdriver and turn the saw table (18) together with the
scale (26) until the leg of the angle gauge is flush with the
saw blade along its entire length.
– Re-tighten the screws.
If the angle indicator (24) is not aligned with the 0° mark on
the scale (26) following adjustment, loosen the screw (69)
using a cross-headed screwdriver and align the angle indic-
ator along the 0° mark.
Transport (see figure X)
Before transporting the power tool, the following steps must
be carried out:
– Loosen the locking screw (6) if it is tightened. Pull the
tool arm fully forwards and retighten the locking screw.
– Ensure that the depth stop (40) is swung all the way back
and the adjusting screw (39) fits through the recess
without touching the depth stop when you move the tool
arm.
– Push the saw table extensions all the way in and fix them
there.
– Bring the power tool into the transport position.
– Remove all accessories that cannot be securely fitted to
the power tool.
– If possible, transport unused saw blades in an enclosed
container.
– Tie the power cable and hook-and-loop strap (70) to-
gether.
– Carry the power tool by the transport handle (10) or
grasp the recessed handles (28) on the side of the saw
table
Only use the transport devices to transport the power
u
tool and never the protective devices.

Maintenance and Service

Maintenance and cleaning

Pull the plug out of the socket before carrying out any
u
work on the power tool.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by an
after-sales service centre that is authorised to repair Bosch
power tools.
The retracting blade guard must always be able to move
freely and retract automatically. It is therefore important to
keep the area around the retracting blade guard clean at all
times.
Always remove dust and chips after working by blowing out
with compressed air or using a brush.
Clean the guide roller (16) regularly.
English | 41
1 609 92A 5UA | (06.10.2020)

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis