Chairman Of The Board Of Management; Alfred Kärcher Se & Co. Kg; Alfred-Kärcher-Str; 71364 Winnenden (Germany) - Kärcher MC 130 plus Betriebsanleitung

 In case of more serious leaks, have the device checked by
Customer Service.
Pump knocking
 Check the water supply line for leaks.
 Vent the device, see section "Venting the device".
 Contact Customer Service if necessary.
Technical data
Hydraulic connection
Supply from the hydraulic system of the MC 130
Connection output
Water connection
Water supply from the water reservoir of the MC 130
Input temperature (max.)
Performance data
Working pressure
Nozzle size
Max. operating pressure
Flow rate
Recoil force of the trigger gun. (max.)
Determined values in acc. with EN 60335-2-79
Sound level L
pA
K uncertainty
pA
Sound power level L + K uncertainty
WA
Hand-arm vibration value
K uncertainty
Operating materials
Oil volume
Oil type
Dimensions and weights
Weight
Installation declaration
We hereby declare die technical documents according to EC Di-
rective 2006/42/EC (+2009/127/EC) Annex VII Part B have been
created for the incomplete machine described below and that this
conforms to the following points of the directive:
Annex I Points 1.1, 1.2, 1.3, 1.4, 1.5, 1.6 and 1.7. I Point 1.1,
This declaration is invalidated by any changes made to the in-
complete machine that are not approved by us.
Product: Attachment kit
High-pressure clean-
er
Type: 2,851-952.7
Harmonised standards used, based
on:
EN 60335–2–79
Authorities can request the relevant documentation for the in-
complete machine from the documentation supervisor. Docu-
ments are provided via email.
Before commissioning or installation of the incomplete machine,
it must be ensured that the complete machine into which the in-
complete machine is installed conforms to the EC Machinery Di-
rective 2006/42/EC (+2009/127/EC).
Please refer to the EC Declaration of Conformity for the machine
for more information on this.
The signatories act on behalf of and with the authority of the com-
pany management.

Chairman of the Board of Management

Director Regulatory Affairs & Certification
Documentation supervisor:
S. Reiser
Alfred Kärcher SE & Co. KG
78
kW 4.5
°C 60
MPa 7-15
036
MPa 19
l/min 10
N 30
dB(A) 75
dB(A) 3
dB(A) 97
WA
2
m/s 1.6
2
m/s 0.7
l 0.4
SAE 15W-40
kg
English
Alfred-Kärcher-Str. 28 - 40

71364 Winnenden (Germany)

Ph.: +49 7195 14-0
Fax: +49 7195 14-2212
Winnenden, 2017/07/18
Working with the manual suction hose (ex-factory
Filling nozzle, water reservoir
1
Suction hose (125 mm)
2
Lock
3
Handle (adjustable)
4
Switch lever
5
Pulled out: Vacuuming with the suction hose
Pressed in: Work in sweeping mode
Manual suction pipe
6
Cover
7
Suction hose bracket
8
Water hose stowage compartment
9
Water hose
10

Working with the manual suction hose

1. Remove the manual suction hose from the stowage compart-
ment.
2. As necessary:
Connected the water hose provided and open the stop cock le-
ver on the handle.
Close the dosing knobs in the cabin to prevent the emission of
spray water for the suction mouth and sweeper jets, otherwise
there will not be enough spray water for the manual suction
hose.
3. Pull out the switch lever into the "Vacuum with suction hose"
position.
Vacuuming with the manual suction hose
1. Start the engine.
2. Switch on the PTO (at the arm rest control panel).
3. Switch on the blower.
4. As necessary: Switch on the water pump at the control panel.
5. Select the engine speed.
Note
The suction power depends on the set engine speed.
1600 rpm - for light waste
2200 rpm - for normal waste
2500 rpm - for strong, heavy waste
6. Hold the suction pipe by the handle (adjustable) and begin
vacuuming.
Storage of the manual suction hose
1. Set the engine speed to 2200 rpm for installing the manual
suction hose.
2. When using the water hose: Switch off the water pump, dis-
connect the water hose and stop appropriately.
3. Insert the suction pipe with handle, press against the cover
and fasten in position.
option)