Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Safety Messages
Snap-on Tools Company provides safety messages to
cover reasonable situations that may be encountered
when operating, servicing or repairing cordless tools. It
is the responsibility of operators and servicing
technicians to be knowledgeable about the procedures,
tools and materials used, and to satisfy themselves that
the procedures, tools and materials will not compromise
their safety, that of others in the work place or the tool.
General Power Tool
Safety Warnings
Read
all
safety
illustrations and specifications provided with this
power tool. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
SAVE ALL
WARNINGS AND
INSTRUCTIONS FOR
FUTURE
REFERENCE
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery- operated
(cordless) power tool.
Work area safety
• Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
• Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases, or
dust. Power tools create sparks which may ignite the dust
or fumes.
• Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
ZCT838CE Rev. A
CT838/CTQ838
CT861/CTQ861
Cordless Impact Wrench
warnings,
instructions,
Electrical safety
• Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
• Avoid body contact with earthed or grounded surfaces
such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body is
earthed or grounded.
• Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
• Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
• When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
• If operating a power tool in a damp location is
unavoidable, use a ground fault circuit interrupter
(GFCI) protected supply. Use of a GFCI reduces the risk
of electric shock.
AUSTRALIA/NEW ZEALAND:
• If operating a power tool in a damp location is
unavoidable, use a RESIDUAL CURRENT DEVICE
(RCD) protected supply rated 30 mA or less. Use of an
RCD reduces the risk of electric shock.
Personal safety
• Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power
tool while you are tired or under the influence of drugs,
alcohol or medication. A moment of inattention while
operating power tools may result in serious personal
injury.
• Use personal protective equipment. Always wear eye
protection. Personal protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
• Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source and/
or battery pack, picking up or carrying the tool. Carrying
power tools with your finger on the switch or energising
power tools that have the switch on invites accidents.
• Remove any adjusting key or wrench before turning the
power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal
injury.
• Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
• Dress properly. Do not wear loose clothing or jewellery.
Keep your hair, clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair can be caught
in moving parts.
2
BC
(05/21)
Werbung
Inhaltsverzeichnis
