Werbung
Verfügbare Sprachen
Verfügbare Sprachen
II FRAME ASSEMBLY To initially unfold the frame (1) with a basket (2), realise the hooks (PIC.A), and simultaneously pull
both free ends of the frame until you hear a characteristic click of the lock (PIC. B). Slide the rear wheel axles (5) into
designated slots until you hear the lock sound (PIC. C). Slide the front wheels (4) into designated slots until you hear the
lock sound (PIC. D). Slide the ends of the parent handle (3) into the free ends of the frame (PIC. E). Make sure that the snap
buttons are locked/secured.
WARNING! The buggy has pumped wheels. Do not exceed the
maximum permissible pressure in the wheels, the value is
indicated on the wheel tyres.
WARNING! Before using the buggy, make sure that all the
wheels are properly installed.
III CARRYCOT ASSEMBLY Start the assembly of the carrycot by sliding the loose part of the frame (8) into the carrycot slots
(7) (PIC. F). Make sure that the snap buttons are locked (PIC.G). and zip around the perimeter of the attached part (PIC.H)
(Set the position of the rod under the carrycot with the straps and secure it with the fasteners (PIC.I). Now, the carrycot
can be fastened into the pushchair's frame (hear the lock sound of both sides of the pushchair) (PIC.J). The straps should
be hidden under the included mattress when using the pushchair in the carrycot version. When using the carrycot version
of the pushchair, the straps on the sides of the seat (2 on the left and 2 on the right) and under the footrest must remain
unfastened. -CAUTION! When the child starts to sit up independently, attach an additional harness at the attachment
points indicated in (PIC.K).
WARNING! THE PRAM BODY CAN ONLY BE MOUNTED FACING
BACKWARDS (the child faces the person pushing the buggy).
IV ASSEMBLY/DISASSEMBLY OF THE BUMPER BAR, SHADE, FOOT MOOF AND CUP HOLDER The bumper bar (6) can be
used in both the carrycot and stroller versions of the pushchair. Slide the ends of the bumper bar into appropriate slots
until you hear the lock sound on both sides (PIC. L). The bumper bar can be detached from the frame partly or as a whole
by pressing the button on its side/sides.
NOTE! INSTALL THE CANOPY BEFORE USING THE BUGGY
Begin the assembly of the shade (9) by sliding the plastic mountings on the slideway on the frame of the carrycot/seat
(PIC. M). Correct locking is signalised by a gentle click. In the end, secure the shade with hook and loop fasteners, fastening
them into the carrycot/seat. To disassemble the shade, press the buttons (PIC.N) and slide out the mountings from the
slideways.
Begin the assembly of the foot moof (10) by slipping on the cover, then put the loop through the button at the bottom of
the cover as shown (PIC. O-I). Attach the top part of the cover by the snaps located on both sides of the foot moof (PIC. O-
II). Wrap the cover around both sides of the bar, and then insert the buttons through the loops on both sides (PIC. O -III).
Assemble the cup holder (14) on the pin on the right side of the pushchair. (PIC. P).
V TURNING THE CARRYCOT INTO THE SEAT To turn the carrycot into the seat, first connect the ends of the removed straps
behind the backrest and under the seat and the footrest (PIC.Q). When the straps are correctly fastened, the seat should
look as shown in (PIC.R), the seat can be fitted forwards or backwards (adjustment of seat angle described in section X). If
you want to use the stroller with a mattress, put the shoulder, waist and crotch straps through the slots in the mattress.
VI ASSEMBLY OF THE BAG, MOSQUITO NET, RAIN COVER
The pushchair set includes: bag (12), fabric hangers (13), rain cover (16) and a mosquito net (17). Hang the bag on the
parent's handle using the hangers by pulling the strap through the metal loops and securing it with hoop and loop fasteners
(PIC. S).
Place the mosquito net/ rain cover on the pushchair, secure it with a hoop and loop fasteners around the frame (PIC. T).
VII ASSEMBLY/DISASSEMBLY OF THE CAR SEAT The attached adapters (11) are compatible with car seats: Kinderkraft®,
Kiddy®, Maxi Cosi®, Cybex®, BeSafe®, Nuna® and they fit, among others, for models: Kinderkraft Mink, Kiddy Evoluna i-
Size 2, Kiddy Evolution Pro 2, Cybex Aton 5, Cybex Aton M, Cybex Aton M i-Size, Cybex Aton B2, Cybex Aton S2 i-Size, Cybex
Cloud Z i-Size, Maxi Cosi Cabriofix i-Size, Maxi Cosi Pebble Pro, Maxi Cosi 360, Maxi Cosi Rock, Maxi Cosi Tinca, Maxi Cosi
Citi, BeSafe izi Go Modular x1, Britax Romer Baby-Safe 3, Avionaut Pixel, Nuna Pipa next i-Size, Nuna Pipa lite, Nuna Pipa
lite lx, Kinderkraft I-Lite
Slide the adapters into the slots in the frame until you hear the lock sound (PIC. U). Adapters shall be slightly leaned
towards the parent. Slide the car seat onto the adapters and make sure it's secured correctly. The pushchair with a car
28
Werbung
